{"title":"Bromic Heater Mounts \u0026 Recess Kits","description":"\u003cp\u003eMounting hardware made by Bromic for its own heaters. Gas heaters hang from ceiling poles in six lengths, from 9.69 to 41.18 inches, to bring them down from a high ceiling. Platinum Electric and Platinum Electric Marine heaters recess with a standard or low clearance kit, or hang from a tube suspension kit; the Tungsten Electric has its own recess and suspension kits. Eclipse pendants hang from 8, 24 or 48 inch straight poles, a 24 inch curved pole or a wall mount pole.\u003c\/p\u003e\n\u003cp\u003eEach kit fits specific heater models and wattages, so check the listing before ordering. Shop the heaters: \u003ca href=\"\/collections\/bromic-electric-heaters\"\u003eelectric\u003c\/a\u003e or \u003ca href=\"\/collections\/bromic-gas-heaters\"\u003egas\u003c\/a\u003e.\u003c\/p\u003e","products":[{"product_id":"bromic-smart-heat-gas-ceiling-pole-mount","title":"Bromic Smart-Heat Gas Ceiling Pole Mount - 9.69 to 41.18 Inch","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe Bromic Smart-Heat Gas Ceiling Pole Mount hangs a \u003ca href=\"\/products\/bromic-platinum-smart-heat-gas-300-patio-heater\"\u003ePlatinum Smart-Heat Gas\u003c\/a\u003e or \u003ca href=\"\/products\/bromic-tungsten-smart-heat-gas-300-patio-heater\"\u003eTungsten Smart-Heat Gas\u003c\/a\u003e heater (300 or 500 series, propane or natural gas) below a ceiling or support beam, so the heater sits at an effective height when the ceiling is too high for a direct mount. It comes in six lengths, from 9.69 in. to 41.18 in., chosen above to suit the ceiling height.\u003c\/p\u003e\n\u003cp\u003eTo pick a length, Bromic adds the pole length to the heater and bracket height of 16.6 in. and subtracts that total from the floor-to-ceiling (or floor-to-beam) distance at the mounting point. The answer is the height from the floor to the bottom of the heater, which must be at least 8 ft. The pole always hangs straight down at 90 degrees to the ground; the adjustment at the top is only there to suit a pitched ceiling, not to angle the heater. Bromic recommends running the gas line and power cord inside the pole, which hides them and protects them from damage.\u003c\/p\u003e\n\u003cp\u003ePlan before ordering: the heater is not included. Check the gap from the top of the heater to the ceiling: Bromic's gas manuals require 3 ft to combustible materials above and beside the heater, or 14 in. above when the matching \u003ca href=\"\/products\/bromic-platinum-gas-heat-deflector\"\u003ePlatinum\u003c\/a\u003e or \u003ca href=\"\/products\/bromic-tungsten-gas-heat-deflector\"\u003eTungsten\u003c\/a\u003e heat deflector is fitted. Installation is by authorized personnel only, into a ceiling or beam strong enough to carry the heater.\u003c\/p\u003e\n\u003cul class=\"mnk-glance\"\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eLengths:\u003c\/strong\u003e 9.69, 13.62, 17.56, 25.43, 33.31, 41.18 in.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFits:\u003c\/strong\u003e Platinum and Tungsten Smart-Heat Gas 300 and 500\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eHeater and bracket height:\u003c\/strong\u003e 16.6 in.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eMinimum heater height:\u003c\/strong\u003e 8 ft above the floor\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"features\"\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSix lengths:\u003c\/strong\u003e 9.69 to 41.18 in., so the heater can be brought down to an effective height under a range of ceiling heights.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSimple sizing rule:\u003c\/strong\u003e ceiling height minus (pole length + 16.6 in.) gives the heater height, so the right length can be picked before ordering.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHidden services:\u003c\/strong\u003e the gas line and power cord can run inside the pole, out of sight and out of harm's way.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePitched-ceiling adjustment:\u003c\/strong\u003e the top mounting point adjusts so the pole still hangs plumb under a sloped ceiling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo lower paddles:\u003c\/strong\u003e bolted back to back on the pole to carry the heater body.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOne pole for both gas ranges:\u003c\/strong\u003e fits Platinum and Tungsten Smart-Heat Gas heaters in either size and fuel.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eIdentification\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eSmart-Heat Gas mounting accessory\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eType\u003c\/th\u003e\n\u003ctd\u003eCeiling pole mount (Bromic: Gas Mounting Poles)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003ePlatinum Smart-Heat Gas 300 and 500; Tungsten Smart-Heat Gas 300 and 500; propane or natural gas (heater not included)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eLengths and part numbers\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e9.69 in.\u003c\/th\u003e\n\u003ctd\u003eBH3030003\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e13.62 in.\u003c\/th\u003e\n\u003ctd\u003eBH3030004\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e17.56 in.\u003c\/th\u003e\n\u003ctd\u003eBH3030005\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e25.43 in.\u003c\/th\u003e\n\u003ctd\u003eBH3030006\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e33.31 in.\u003c\/th\u003e\n\u003ctd\u003eBH3030007\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e41.18 in.\u003c\/th\u003e\n\u003ctd\u003eBH3030008\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eMounting and clearances\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater and bracket height\u003c\/th\u003e\n\u003ctd\u003e16.6 in. (added to the pole length)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePole orientation\u003c\/th\u003e\n\u003ctd\u003eVertical, 90 degrees to the ground, on flat or pitched ceilings\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCeiling fixings\u003c\/th\u003e\n\u003ctd\u003eAt least 60 mm (2.4 in.) long, into the ceiling or a support beam (installer supplied)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLower paddles\u003c\/th\u003e\n\u003ctd\u003eTwo, fitted back to back with three M10 x 100 mm bolts, nuts and washers\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMinimum heater height\u003c\/th\u003e\n\u003ctd\u003e8 ft above the floor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eClearance above and beside heater\u003c\/th\u003e\n\u003ctd\u003e3 ft to combustibles; 14 in. above with the heat deflector\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eGas and power routing\u003c\/th\u003e\n\u003ctd\u003eInside the pole (Bromic recommendation)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003cdiv class=\"mnk-kit\"\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"whats-included\"\u003eWhat's included\u003c\/h3\u003e\n\u003cul class=\"mnk-included\"\u003e\n\u003cli\u003eGas mounting pole in the length selected\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBromic does not publish a packing list. The manual's mounting steps use a top bracket, the pole and two lower paddles joined with bolts, nuts and washers; ask us to confirm the contents for your length before ordering. Not included: the heater, the ceiling fixings and the fixtures that attach the heater to the paddles.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"sold-separately\"\u003eSold separately\u003c\/h3\u003e\n\u003cul class=\"mnk-optional\"\u003e\n\u003cli\u003eHeaters: \u003ca href=\"\/products\/bromic-platinum-smart-heat-gas-300-patio-heater\"\u003ePlatinum Gas 300\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-gas-500-patio-heater\"\u003ePlatinum Gas 500\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-tungsten-smart-heat-gas-300-patio-heater\"\u003eTungsten Gas 300\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-tungsten-smart-heat-gas-500-patio-heater\"\u003eTungsten Gas 500\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/bromic-platinum-gas-heat-deflector\"\u003ePlatinum Gas Heat Deflector\u003c\/a\u003e or \u003ca href=\"\/products\/bromic-tungsten-gas-heat-deflector\"\u003eTungsten Gas Heat Deflector\u003c\/a\u003e, to cut the clearance above the heater to 14 in.\u003c\/li\u003e\n\u003cli\u003eCSA approved flexible gas connector with 3\/8 in. SAE flared ends (supplied by the installer)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003ch3 id=\"installation\"\u003eInstallation planning\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eChoosing the length:\u003c\/strong\u003e measure from the floor to the ceiling or beam where the pole will mount. Subtract the pole length plus 16.6 in.; the result is the height of the bottom of the heater, which must be at least 8 ft.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClearances to combustibles:\u003c\/strong\u003e keep overhead structures, walls and plants at least 3 ft from the top and sides of the heater. With the heat deflector fitted, the clearance above drops to 14 in.; the side clearance and 8 ft minimum height stay the same.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting steps (from the manual):\u003c\/strong\u003e fix the top bracket to the ceiling or a support beam with fixings at least 60 mm (2.4 in.) long; bolt the pole to the bracket; fit both lower paddles to the pole back to back with three M10 x 100 mm bolts, nuts and washers; then fix the heater to the paddles with suitable fixtures.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStructure:\u003c\/strong\u003e the anchoring must have enough strength, quality and workmanship to support the heater and any other load on the fixture.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePlumb pole:\u003c\/strong\u003e the pole must hang at 90 degrees to the ground whether the ceiling is flat or pitched.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGas and power:\u003c\/strong\u003e run both inside the pole. Use a CSA approved flexible gas connector; replacement hoses must have 3\/8 in. SAE flared ends, be leak tested with soapy water and be checked every year. Keep the hose out of walkways.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstaller:\u003c\/strong\u003e installation and service by authorized personnel only, to local codes.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCare:\u003c\/strong\u003e Bromic asks for the heater's control compartment, burner and air passages to be inspected and cleaned at least every six months, more often in harsh or salt-air conditions, and for the gas hose to be checked every year and replaced if worn or damaged.\u003c\/p\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's warranty page does not list a separate term for the gas mounting poles. Platinum Gas and Tungsten Gas heaters are covered for 2 years, excluding maintenance items such as hoses and igniters, for the original owner only. Bromic supplies a replacement heater or part; the owner pays labor, removal and reinstallation, shipping both ways and other costs. Implied warranties are limited to one year. Claims start with the dealer who sold the product. Ask us to confirm the pole's coverage before you order.\u003c\/p\u003e\n\u003ch3 id=\"manuals\"\u003eManuals and documents\u003c\/h3\u003e\n\u003cul class=\"mnk-docs\"\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/Bromic-Platinum-Smart-Heat-Gas-Instruction-Manual-US-V2.43.pdf\" target=\"_blank\" rel=\"noopener\"\u003ePlatinum Smart-Heat Gas installation, instruction and service manual, USA\/Canada (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eCeiling pole mounting, clearances, gas hose\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2026\/05\/Manual-Tungsten-Gas-V2.3.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTungsten Smart-Heat Gas installation, instruction and service manual, Version 2.3 USA\/Canada (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eCeiling pole mounting, clearances, care\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/product\/gas-mounting-poles\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic Gas Mounting Poles product page\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eLengths, fit, height calculation\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/warranty\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic warranty terms\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eWarranty periods by product line\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"9.69 in.","offer_id":68167512260887,"sku":"BH3030003","price":368.0,"currency_code":"USD","in_stock":true},{"title":"13.62 in.","offer_id":68167512293655,"sku":"BH3030004","price":368.0,"currency_code":"USD","in_stock":true},{"title":"17.56 in.","offer_id":68167512326423,"sku":"BH3030005","price":368.0,"currency_code":"USD","in_stock":true},{"title":"25.43 in.","offer_id":68167512359191,"sku":"BH3030006","price":368.0,"currency_code":"USD","in_stock":true},{"title":"33.31 in.","offer_id":68167512391959,"sku":"BH3030007","price":368.0,"currency_code":"USD","in_stock":true},{"title":"41.18 in.","offer_id":68167512424727,"sku":"BH3030008","price":368.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-smart-heat-gas-ceiling-pole-mount-9-69-to-41-18-inch-bh3030003-bh3030004-bh3030005-and.jpg?v=1794343445"},{"product_id":"bromic-platinum-electric-ceiling-recess-kit","title":"Bromic Platinum Electric Ceiling Recess Kit - 2300W, 3400W or 4500W","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe Bromic Platinum Electric Ceiling Recess Kit is Bromic's standard-clearance kit for flush-mounting a \u003ca href=\"\/collections\/bromic-heating\"\u003ePlatinum Smart-Heat Electric heater\u003c\/a\u003e into the ceiling, so only the heater face shows below the ceiling line. Bromic describes it as ideal for new builds that leave more cavity space above the ceiling. The kit is brushed grade 304 stainless steel, the same grade as the standard Platinum Electric heaters, and comes with the parts and hardware needed for recessed mounting.\u003c\/p\u003e\n\u003cp\u003eChoose the kit size above to match your heater: BH3130017 for the \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-2300w-patio-heater\"\u003ePlatinum Electric 2300W\u003c\/a\u003e, BH3130027 for the \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-3400w-patio-heater\"\u003e3400W\u003c\/a\u003e or BH3623000 for the \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-4500w-patio-heater\"\u003e4500W\u003c\/a\u003e. The heater is not included. For grade 316 Marine heaters, see the \u003ca href=\"\/products\/bromic-platinum-electric-marine-ceiling-recess-kit\"\u003eMarine Ceiling Recess Kit\u003c\/a\u003e. Where the ceiling cavity is shallow, the \u003ca href=\"\/products\/bromic-platinum-electric-low-clearance-recess-kit\"\u003eLow Clearance Recess Kit\u003c\/a\u003e works in as little as 7.1 in. of vertical space and adds its own cooling fan.\u003c\/p\u003e\n\u003cp\u003ePlan before ordering: the ceiling lining must be 10 to 30 mm (0.4 to 1.2 in.) thick, the heater face must sit at least 2400 mm (94 in.) above the floor, and joists, beams and rafters must not be cut. The cavity needs the clearances to combustibles shown in Bromic's manual, the heater must never be covered with insulation, and it must be fully protected from water above. A licensed electrician installs and hard-wires it.\u003c\/p\u003e\n\u003cul class=\"mnk-glance\"\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFits:\u003c\/strong\u003e Platinum Electric 2300W, 3400W, 4500W\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eMaterial:\u003c\/strong\u003e Brushed stainless steel, grade 304\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eCeiling thickness:\u003c\/strong\u003e 0.4 to 1.2 in.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eHeater height:\u003c\/strong\u003e 94 in. minimum above the floor\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eUse:\u003c\/strong\u003e Land-based and coastal sites\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"features\"\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFlush ceiling finish:\u003c\/strong\u003e the heater sits up in the recess frame, so only its face shows below the ceiling line.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrade 304 stainless:\u003c\/strong\u003e matches the standard Platinum Electric heaters in black or white.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSized to each heater:\u003c\/strong\u003e separate kits for the 2300W, 3400W and 4500W heaters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorks with standard ceiling linings:\u003c\/strong\u003e 10 to 30 mm (0.4 to 1.2 in.) thick; Bromic advises on thicker ceilings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUses the heater's own bracket:\u003c\/strong\u003e the heater bracket hooks into the recess mounting plate, and the power cable enters through an extra cable gland.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eIdentification\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003ePlatinum Smart-Heat Electric, Ceiling Recess Kit (standard clearance)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart numbers\u003c\/th\u003e\n\u003ctd\u003eBH3130017 (2300W), BH3130027 (3400W), BH3623000 (4500W, EU\/UK\/US\/CA)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003ePlatinum Smart-Heat Electric Series II 2300W, 3400W and 4500W heaters (heater not included)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrushed stainless steel, grade 304\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eCeiling and clearances\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCeiling lining thickness\u003c\/th\u003e\n\u003ctd\u003e10 to 30 mm (0.4 to 1.2 in.); thicker ceilings: contact Bromic\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater face above floor\u003c\/th\u003e\n\u003ctd\u003e2400 mm (94 in.) minimum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eTo nearest wall\u003c\/th\u003e\n\u003ctd\u003e500 mm (20 in.) minimum, on all sides\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBetween heaters\u003c\/th\u003e\n\u003ctd\u003e500 mm (20 in.) minimum, from the heater edge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCut-out and cavity clearances\u003c\/th\u003e\n\u003ctd\u003eShown on the manual's recess diagrams; for the 2300W and 3400W use one clearance option only, never a mix of the two\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eHeater it carries (for structural planning)\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e2300W\u003c\/th\u003e\n\u003ctd\u003e840 x 182 x 54 mm (33.0 x 7.0 x 2.0 in.), 7.5 kg (16.5 lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e3400W\u003c\/th\u003e\n\u003ctd\u003e1275 x 182 x 54 mm (50.2 x 7.0 x 2.0 in.), 10 kg (22 lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e4500W\u003c\/th\u003e\n\u003ctd\u003e1351 x 257 x 54 mm (53.2 x 10.1 x 2.1 in.), 15 kg (33 lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eElectrical (heater)\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCurrent, 2300W\u003c\/th\u003e\n\u003ctd\u003e11.1 A at 208V; 9.6 A at 220-240V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCurrent, 3400W\u003c\/th\u003e\n\u003ctd\u003e16.3 A at 208V; 14.2 A at 220-240V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCurrent, 4500W\u003c\/th\u003e\n\u003ctd\u003e21.6 A at 208V; 18.8 A at 220-240V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eConnection\u003c\/th\u003e\n\u003ctd\u003ePermanently hard-wired and grounded, by a licensed person\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eUse\u003c\/th\u003e\n\u003ctd\u003eRecess installs: land-based and coastal sites only\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003cdiv class=\"mnk-kit\"\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"whats-included\"\u003eWhat's included\u003c\/h3\u003e\n\u003cul class=\"mnk-included\"\u003e\n\u003cli\u003eCeiling recess frame and the parts and hardware for recessed mounting (Bromic product page)\u003c\/li\u003e\n\u003cli\u003eParts the manual's recess steps call for: an extra cable gland, a two-piece recess mounting plate, a bracket end-cap with M5 screws and nuts, straight covers, M6 x 14 mm mounting screws and M4 x 10 mm positioning screws\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBromic does not publish a separate packing list. Not included: the heater and the fasteners into the ceiling structure.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"sold-separately\"\u003eSold separately\u003c\/h3\u003e\n\u003cul class=\"mnk-optional\"\u003e\n\u003cli\u003eHeaters: \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-2300w-patio-heater\"\u003ePlatinum Electric 2300W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-3400w-patio-heater\"\u003e3400W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-4500w-patio-heater\"\u003e4500W\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eControls: \u003ca href=\"\/products\/bromic-affinity-smart-heat-on-off-controller\"\u003eAffinity Smart-Heat On\/Off\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-affinity-smart-heat-dimmer-controller\"\u003eAffinity Smart-Heat Dimmer\u003c\/a\u003e or the \u003ca href=\"\/products\/bromic-manual-wall-switch-heater-kit\"\u003eBromic manual wall switch kit\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eFor shallow cavities: \u003ca href=\"\/products\/bromic-platinum-electric-low-clearance-recess-kit\"\u003eLow Clearance Recess Kit\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eFor Marine heaters: \u003ca href=\"\/products\/bromic-platinum-electric-marine-ceiling-recess-kit\"\u003eMarine Ceiling Recess Kit\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003ch3 id=\"installation\"\u003eInstallation planning\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstaller:\u003c\/strong\u003e a licensed, authorized person, to local electrical codes. The heater is permanently hard-wired to a supply that matches its rating label and is properly grounded. Switch off the power before installation or maintenance.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStructure:\u003c\/strong\u003e do not cut or notch joists, beams or rafters. Fix the frame at both ends and the center into structural members strong enough to carry the heater (reinforcement may be needed). The locator hole used depends on the ceiling thickness.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCavity:\u003c\/strong\u003e keep the clearances to combustibles shown in the manual's recess diagrams. They are fixed minimums and, for the 2300W and 3400W, the two clearance options cannot be combined. Never cover the heater with insulation or similar material, and protect it fully from water from above.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeight and spacing:\u003c\/strong\u003e heater face at least 2400 mm (94 in.) above the floor, at least 500 mm (20 in.) from the nearest wall on all sides and at least 500 mm (20 in.) between heaters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSequence:\u003c\/strong\u003e cut the opening to the manual's cut-out drawing, fit the recess frame, swap the heater's wall bracket for the extra cable gland, fit the bracket covers and end-cap, add the two-piece mounting plate, make the electrical connection, then raise the heater into the cavity, rotate it level and lower it so the brackets hook into the frame slots.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFront clearance:\u003c\/strong\u003e Bromic's heater manuals call for 1000 mm (39.4 in.) clear in front of the heater, with combustibles kept at least 1000 mm away.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCare:\u003c\/strong\u003e Switch off and let the heater cool (Bromic says at least 2 hours) before cleaning. Inspect and clean the body and structure at least monthly, and wipe it with a soft damp cloth every two weeks in coastal areas. Do not use steam cleaners or touch the glass surface. Have the heater inspected before use and serviced at least once a year by a qualified, licensed person.\u003c\/p\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's published warranty page does not list a separate term for recess kits. It covers Platinum Electric heaters for 3 years, for the original owner only, from the date of purchase. Bromic supplies a replacement heater or part; the owner pays service, removal and reinstallation labor, shipping and other costs. Implied warranties are limited to one year. Claims start with the dealer who sold the product. Ask us to confirm the kit's coverage before you order.\u003c\/p\u003e\n\u003ch3 id=\"manuals\"\u003eManuals and documents\u003c\/h3\u003e\n\u003cul class=\"mnk-docs\"\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/Bromic-Platinum-Smart-Heat-Electric-SII-Instruction-Manual-US_v4.pdf\" target=\"_blank\" rel=\"noopener\"\u003ePlatinum Smart-Heat Electric Series II 2300W \/ 3400W manual, US version 4 (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eRecess kit part numbers, recess steps and cut-out drawing, clearance options, specifications, care\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/Bromic-Platinum-Smart-Heat-Electric-SII-Instruction-Manual-4.5kW-AU-UK-US_v1.1.pdf\" target=\"_blank\" rel=\"noopener\"\u003ePlatinum Smart-Heat Electric Series II 4500W manual, version 1.3 (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003e4500W recess kit part numbers, cut-out, clearances, specifications\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/product\/platinum-electric-recess-kit\" target=\"_blank\" rel=\"noopener\"\u003eBromic Platinum Electric Recess Kits product page\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eSizes and compatibility\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/warranty\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic warranty terms\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eWarranty periods by product line\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"2300W","offer_id":68167512457495,"sku":"BH3130017","price":534.0,"currency_code":"USD","in_stock":true},{"title":"3400W","offer_id":68167512490263,"sku":"BH3130027","price":632.0,"currency_code":"USD","in_stock":true},{"title":"4500W","offer_id":68167512523031,"sku":"BH3623000","price":720.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-platinum-electric-ceiling-recess-kit-2300w-3400w-or-bh3130017-bh3130027-bh3623000-recess.jpg?v=1794343282"},{"product_id":"bromic-platinum-electric-low-clearance-recess-kit","title":"Bromic Platinum Electric Low Clearance Ceiling Recess Kit - 2300W, 3400W or 4500W","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe Bromic Platinum Electric Low Clearance Ceiling Recess Kit flush-mounts a \u003ca href=\"\/collections\/bromic-heating\"\u003ePlatinum Smart-Heat Electric heater\u003c\/a\u003e into a ceiling cavity with as little as 7.1 in. of vertical space. The recess box fits within standard ceiling joists, and a built-in frame and integrated cooling fan manage temperature in the cavity, so recessed heat is possible in a new build or a retrofit where a standard recess kit would not fit. Bromic describes the Low Clearance kit as UL certified.\u003c\/p\u003e\n\u003cp\u003eChoose the kit size above to match your heater: 2300W (BH3623009-1), 3400W (BH3623008-1) or 4500W (BH3623012-1), to suit the \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-2300w-patio-heater\"\u003ePlatinum Electric 2300W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-3400w-patio-heater\"\u003e3400W\u003c\/a\u003e or \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-4500w-patio-heater\"\u003e4500W\u003c\/a\u003e heater. This standard kit is brushed grade 304 stainless steel and comes with both black and white vent covers so they can match the heater color. The heater itself is not included. For coastal sites, the grade 316 \u003ca href=\"\/products\/bromic-platinum-electric-marine-low-clearance-recess-kit\"\u003eMarine Low Clearance kit\u003c\/a\u003e suits the Marine heaters; where the cavity is deeper, Bromic also makes a standard-clearance \u003ca href=\"\/products\/bromic-platinum-electric-ceiling-recess-kit\"\u003ePlatinum Electric Ceiling Recess Kit\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003ePlan before ordering: the integrated fan needs its own constant power supply that is live at all times (not after a switch) and runs independently of the heater. The ceiling cut-out must sit between joists without cutting them, the heater face must be at least 2400 mm above the finished floor, the recess must be fully protected from water from above, and installation is by a licensed technician with two people.\u003c\/p\u003e\n\u003cul class=\"mnk-glance\"\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eCavity depth:\u003c\/strong\u003e 7.1 in. minimum\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eSizes:\u003c\/strong\u003e 2300W, 3400W, 4500W heaters\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eMaterial:\u003c\/strong\u003e Grade 304 stainless steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFan supply:\u003c\/strong\u003e 100-127V, 208V or 220-240V, under 1 A\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eCeiling thickness:\u003c\/strong\u003e 0.39 to 1.18 in.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"features\"\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e7.1 in. cavity:\u003c\/strong\u003e flush-mounts the heater where ceiling space is shallow, within standard joist spacing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIntegrated cooling fan and frame:\u003c\/strong\u003e keep the recess cavity within temperature limits, on a dedicated always-on supply.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorks with every Platinum Electric finish:\u003c\/strong\u003e black and white vent covers are both in the box, so the ceiling finish matches your heater.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eComplete recess hardware:\u003c\/strong\u003e recess box, IP cover, terminal box, trims and screws are included; ceiling fasteners are supplied by the installer.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSeparate element control on 4500W:\u003c\/strong\u003e the larger kit has a 12-terminal block and connectors so the 1500W and 3000W elements can run on separate switches.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThermal protection:\u003c\/strong\u003e a self-resetting thermal switch must be plugged in for the heater to run, and a manual-reset thermal switch in the terminal box trips on over-temperature.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eIdentification\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003ePlatinum Smart-Heat Electric, Low Clearance (LC) Ceiling Recess Kit, standard\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart numbers\u003c\/th\u003e\n\u003ctd\u003eBH3623009-1 (2300W), BH3623008-1 (3400W), BH3623012-1 (4500W)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003ePlatinum Smart-Heat Electric 2300W, 3400W and 4500W heaters (heater not included)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eCeiling cut-out\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e2300W\u003c\/th\u003e\n\u003ctd\u003e995 x 240 mm (39.2 x 9.4 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e3400W\u003c\/th\u003e\n\u003ctd\u003e1430 x 240 mm (56.3 x 9.4 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e4500W\u003c\/th\u003e\n\u003ctd\u003e1550 x 317 mm (61.0 x 12.5 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eKit size (L x W x H)\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e2300W\u003c\/th\u003e\n\u003ctd\u003e1039 x 261 x 175 mm (40.9 x 10.3 x 6.9 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e3400W\u003c\/th\u003e\n\u003ctd\u003e1475 x 261 x 175 mm (58.1 x 10.3 x 6.9 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e4500W\u003c\/th\u003e\n\u003ctd\u003e1595 x 338 x 178 mm (62.8 x 13.3 x 7.0 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eInstalled weight with heater (structural planning)\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e2300W\u003c\/th\u003e\n\u003ctd\u003e18.5 kg (41 lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e3400W\u003c\/th\u003e\n\u003ctd\u003e24 kg (53 lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eClearances\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eVertical space above ceiling\u003c\/th\u003e\n\u003ctd\u003e180 mm (7.1 in.) minimum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eTerminal box end to nearest surface\u003c\/th\u003e\n\u003ctd\u003e200 mm (7.9 in.) minimum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCut-out to nearest wall\u003c\/th\u003e\n\u003ctd\u003e500 mm (19.7 in.) minimum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBetween heaters\u003c\/th\u003e\n\u003ctd\u003e500 mm (19.7 in.) minimum, from cut-out edge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater surface to finished floor\u003c\/th\u003e\n\u003ctd\u003e2400 mm minimum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSpace between joists\u003c\/th\u003e\n\u003ctd\u003e240 mm (9.4 in.) for 2300W and 3400W; 317 mm (12.5 in.) for 4500W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eBuild and electrical\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrushed stainless steel, grade 304\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCeiling thickness\u003c\/th\u003e\n\u003ctd\u003e10 to 30 mm (0.39 to 1.18 in.); thicker ceilings: contact Bromic\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFan supply\u003c\/th\u003e\n\u003ctd\u003e100-127V AC 50\/60 Hz, 208V AC 60 Hz or 220-240V AC 50\/60 Hz; under 1.0 A; constant, unswitched\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater circuit current\u003c\/th\u003e\n\u003ctd\u003e2300W: 11.1 A at 208V, 9.6 A at 220-240V. 3400W: 16.3 A \/ 14.2 A. 4500W: 21.6 A \/ 18.8 A (1500W element 7.2 A \/ 6.3 A; 3000W element 14.4 A \/ 12.5 A)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCable gland\u003c\/th\u003e\n\u003ctd\u003eM16 (2300W, 3400W); M20 (4500W)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMinimum heater supply cable length\u003c\/th\u003e\n\u003ctd\u003e800 mm (2300W), 1000 mm (3400W), 1040 mm (4500W)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eTerminal wire size\u003c\/th\u003e\n\u003ctd\u003e10 AWG (6.0 mm²) maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eOutdoor wiring parts\u003c\/th\u003e\n\u003ctd\u003eIPX5 or better\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCertification\u003c\/th\u003e\n\u003ctd\u003eUL certified (Bromic product page)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003cdiv class=\"mnk-kit\"\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"whats-included\"\u003eWhat's included\u003c\/h3\u003e\n\u003cul class=\"mnk-included\"\u003e\n\u003cli\u003eCeiling recess box with integrated cooling fan\u003c\/li\u003e\n\u003cli\u003eIP cover and terminal box\u003c\/li\u003e\n\u003cli\u003eBlack and white vent covers, with vent cover trims\u003c\/li\u003e\n\u003cli\u003eStandard trim assembly\u003c\/li\u003e\n\u003cli\u003eScrews: 8 x M3x6, 8 x M4x8, 1 x M6x10\u003c\/li\u003e\n\u003cli\u003e3-way WAGO connectors (4500W kit only)\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot included: the heater and the fasteners into the ceiling structure.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"sold-separately\"\u003eSold separately\u003c\/h3\u003e\n\u003cul class=\"mnk-optional\"\u003e\n\u003cli\u003eHeaters: \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-2300w-patio-heater\"\u003ePlatinum Electric 2300W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-3400w-patio-heater\"\u003e3400W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-4500w-patio-heater\"\u003e4500W\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eControls shown in the wiring diagrams: \u003ca href=\"\/products\/bromic-affinity-smart-heat-dimmer-controller\"\u003eAffinity Smart-Heat Dimmer\u003c\/a\u003e (1 channel), \u003ca href=\"\/products\/bromic-affinity-smart-heat-on-off-controller\"\u003eAffinity Smart-Heat On\/Off\u003c\/a\u003e (2 channel, for separate element control on the 4500W), or a wall switch such as the \u003ca href=\"\/products\/bromic-manual-wall-switch-heater-kit\"\u003eBromic manual wall switch kit\u003c\/a\u003e; Bromic recommends two 20 A switches for the 4500W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003ch3 id=\"installation\"\u003eInstallation planning\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstaller:\u003c\/strong\u003e a licensed, authorized person, to local electrical codes. Disconnect power during installation and maintenance; the heater must be off and cooled for 2 hours before handling. At least two people are needed for the lifting steps (16 kg maximum safe lift per person).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStructure:\u003c\/strong\u003e do not cut or notch joists, beams or rafters. Fix the recess box with at least 6 suitable fasteners along the long edge (at least 10 into timber members), into material that can carry the assembly; reinforcement may be needed, and the installer confirms the structure can carry the load.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCavity:\u003c\/strong\u003e at least 180 mm (7.1 in.) of vertical space, 200 mm (7.9 in.) at the terminal box end and 500 mm (19.7 in.) from the cut-out to the nearest wall. Never cover the kit or heater with insulation or similar material.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeather:\u003c\/strong\u003e protect the recess fully from water from above. Standard (grade 304) heaters must not be directly exposed to rain; use the Marine kit and heater for coastal sites.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeight and spacing:\u003c\/strong\u003e heater surface at least 2400 mm above the finished floor, and at least 500 mm between heaters from the cut-out edge.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWiring:\u003c\/strong\u003e the fan supply must be constant and live at all times, not after a switch, so the fan runs independently of the heater. Rest the heater supply cable on the support structure, never on the heater's rear surface. Use outdoor wiring parts rated IPX5 or better; terminals take up to 10 AWG. The 4500W kit can take separate supplies to control each element.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThermal switch:\u003c\/strong\u003e plug the self-resetting thermal switch into the terminal box receptacle, or the heater will not run.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCare:\u003c\/strong\u003e Switch off and wait at least 2 hours before cleaning. Clean the exterior every two weeks with a soft, damp cloth, more often in coastal or harsh conditions. Only an authorized, licensed service person may service it; do not run a malfunctioning heater, and have an electrician inspect it before it is used again. A damaged supply cord must be replaced by Bromic, its service agent or a similarly qualified person. If the manual-reset thermal switch in the terminal box trips (often a fan fault or high ambient temperature), reset it by pressing its center button only with the circuit de-energized.\u003c\/p\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's published warranty page does not list a separate term for recess kits. It covers Platinum Electric heaters for 3 years from purchase, for the original owner, with Bromic supplying a replacement heater or part and the owner paying labor, removal, reinstallation and shipping costs. Claims start with the dealer that sold the heater. Ask us to confirm the kit's coverage before you order.\u003c\/p\u003e\n\u003ch3 id=\"manuals\"\u003eManuals and documents\u003c\/h3\u003e\n\u003cul class=\"mnk-docs\"\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2025\/12\/Bromic-Platinum-Electric-Low-Clearance-Recess-Kit-Manual-EN.pdf\" target=\"_blank\" rel=\"noopener\"\u003ePlatinum Smart-Heat Electric Low Clearance Ceiling Recess installation instructions, REV10 (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003ePart numbers, cut-outs, clearances, structure, wiring, care\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2025\/05\/LCRK-Affinity-Wiring-Guide-NA.pdf\" target=\"_blank\" rel=\"noopener\"\u003eLCRK Affinity wiring guide, North America (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eFan, heater and Affinity 1 channel wiring, earlier control box revision\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/product\/platinum-electric-low-clearance-recess-kit\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic Platinum Electric Low-Clearance Recess Kit product page\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eSizes, compatibility, installation video\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/warranty\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic warranty terms\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eWarranty periods by product line\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"2300W","offer_id":68167513866519,"sku":"BH3623009-1","price":1309.0,"currency_code":"USD","in_stock":true},{"title":"3400W","offer_id":68167513899287,"sku":"BH3623008-1","price":1385.0,"currency_code":"USD","in_stock":true},{"title":"4500W","offer_id":68167513932055,"sku":"BH3623012-1","price":1844.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-platinum-electric-low-clearance-ceiling-recess-kit-bh3623009-1-bh3623008-1-bh3623012-1.jpg?v=1794343282"},{"product_id":"bromic-platinum-electric-tube-suspension-kit","title":"Bromic Platinum Electric Tube Suspension Kit - 600 mm or 1200 mm","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe Bromic Platinum Electric Tube Suspension Kit is a brushed grade 304 stainless steel ceiling pole that hangs a \u003ca href=\"\/collections\/bromic-heating\"\u003ePlatinum Smart-Heat Electric heater\u003c\/a\u003e below a high ceiling, bringing the heat down toward the seating area. Bromic makes it in two lengths, 600 mm (23.62 in.) and 1200 mm (47.24 in.), in the same 304 stainless steel as the standard \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-2300w-patio-heater\"\u003ePlatinum Electric 2300W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-3400w-patio-heater\"\u003e3400W\u003c\/a\u003e and \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-4500w-patio-heater\"\u003e4500W\u003c\/a\u003e heaters.\u003c\/p\u003e\n\u003cp\u003eChoose the heater size and pole length above. Bromic's manuals list BH3130023-1 (600 mm) and BH3130024-1 (1200 mm) as the US and Canada tube suspension kits, in both the 2300W \/ 3400W manual and the 4500W manual. We also list 4500W options under BH3623020 and BH3623021; those part numbers do not appear in Bromic's manuals, so ask us to confirm the right kit for a 4500W heater before you order. For Marine heaters, the grade 316 \u003ca href=\"\/products\/bromic-platinum-electric-marine-tube-suspension-kit\"\u003eMarine Tube Suspension Kit\u003c\/a\u003e is the match.\u003c\/p\u003e\n\u003cp\u003ePlan before ordering: the pole is for ceiling mounting only and must never be wall-mounted. It is used with a ceiling bracket, sold separately, in place of the mounting bracket that comes with the heater. Bromic's minimum is 2400 mm (96 in.) from the floor to the heater surface, so pick a length that keeps the heater above that. The heater itself is not included, and a licensed electrician installs and hard-wires it.\u003c\/p\u003e\n\u003cul class=\"mnk-glance\"\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eLengths:\u003c\/strong\u003e 600 mm (23.62 in.) or 1200 mm (47.24 in.)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eMaterial:\u003c\/strong\u003e Brushed stainless steel, grade 304\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eMounting:\u003c\/strong\u003e Ceiling only\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFits:\u003c\/strong\u003e Platinum Electric heaters\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eHeater height:\u003c\/strong\u003e 96 in. minimum above the floor\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"features\"\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo drop lengths:\u003c\/strong\u003e 600 mm (23.62 in.) or 1200 mm (47.24 in.), to bring a heater down from a high ceiling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrade 304 stainless:\u003c\/strong\u003e matches the standard Platinum Electric heaters in black or white.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCeiling-only design:\u003c\/strong\u003e the pole hangs the heater from above; Bromic does not allow wall mounting with it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAngled or face-down:\u003c\/strong\u003e Bromic's suspension diagrams show the heater hung face-down or tilted at 28 degrees.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eIdentification\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003ePlatinum Smart-Heat Electric, Tube Suspension Kit (standard)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart numbers (Bromic manuals, US\/CA)\u003c\/th\u003e\n\u003ctd\u003eBH3130023-1 (600 mm), BH3130024-1 (1200 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eOur 4500W options\u003c\/th\u003e\n\u003ctd\u003eBH3623020 (600 mm), BH3623021 (1200 mm); ask us to confirm fit\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003ePlatinum Smart-Heat Electric Series II heaters (heater not included)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eBuild\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLength\u003c\/th\u003e\n\u003ctd\u003e600 mm (23.62 in.) or 1200 mm (47.24 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrushed stainless steel, grade 304\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMounting\u003c\/th\u003e\n\u003ctd\u003eCeiling only; do not wall-mount\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBracket\u003c\/th\u003e\n\u003ctd\u003eCeiling bracket, sold separately, replaces the heater's supplied mounting bracket\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eHeater it carries\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e2300W\u003c\/th\u003e\n\u003ctd\u003e840 x 182 x 54 mm (33.0 x 7.0 x 2.0 in.), 7.5 kg (16.5 lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e3400W\u003c\/th\u003e\n\u003ctd\u003e1275 x 182 x 54 mm (50.2 x 7.0 x 2.0 in.), 10 kg (22 lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e4500W\u003c\/th\u003e\n\u003ctd\u003e1351 x 257 x 54 mm (53.2 x 10.1 x 2.1 in.), 15 kg (33 lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eClearances\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater surface above floor\u003c\/th\u003e\n\u003ctd\u003e2400 mm (96 in.) minimum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFront\u003c\/th\u003e\n\u003ctd\u003e1000 mm (39.4 in.) clear; combustibles at least 1000 mm away\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBetween heaters\u003c\/th\u003e\n\u003ctd\u003e500 mm (20 in.) minimum, from the heater edge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003cdiv class=\"mnk-kit\"\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"whats-included\"\u003eWhat's included\u003c\/h3\u003e\n\u003cul class=\"mnk-included\"\u003e\n\u003cli\u003eBrushed grade 304 stainless steel suspension pole, 600 mm or 1200 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBromic does not publish a packing list for this kit. Not included: the heater, the ceiling bracket and the fasteners into the ceiling structure.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"sold-separately\"\u003eSold separately\u003c\/h3\u003e\n\u003cul class=\"mnk-optional\"\u003e\n\u003cli\u003eHeaters: \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-2300w-patio-heater\"\u003ePlatinum Electric 2300W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-3400w-patio-heater\"\u003e3400W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-4500w-patio-heater\"\u003e4500W\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eCeiling bracket for tube suspension (Bromic; ask us)\u003c\/li\u003e\n\u003cli\u003eControls: \u003ca href=\"\/products\/bromic-affinity-smart-heat-on-off-controller\"\u003eAffinity Smart-Heat On\/Off\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-affinity-smart-heat-dimmer-controller\"\u003eAffinity Smart-Heat Dimmer\u003c\/a\u003e or the \u003ca href=\"\/products\/bromic-manual-wall-switch-heater-kit\"\u003eBromic manual wall switch kit\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eFlush-mount alternatives: \u003ca href=\"\/products\/bromic-platinum-electric-ceiling-recess-kit\"\u003eCeiling Recess Kit\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-electric-low-clearance-recess-kit\"\u003eLow Clearance Recess Kit\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003ch3 id=\"installation\"\u003eInstallation planning\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstaller:\u003c\/strong\u003e the heater must be permanently installed and hard-wired by a licensed, authorized person to local electrical codes, on a grounded supply that matches its rating label. Switch off the power before installation or maintenance.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e ceiling only, using the separately sold ceiling bracket instead of the bracket supplied with the heater. Bromic describes the rest of the installation as the same as ceiling and wall mounting. Fix into structure strong enough to carry the heater and pole.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeight and spacing:\u003c\/strong\u003e heater surface at least 2400 mm (96 in.) above the floor, so choose a pole length that keeps the heater above that. Keep 1000 mm (39.4 in.) clear in front, combustibles at least 1000 mm away and at least 500 mm (20 in.) between heaters, measured from the heater edge.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCare:\u003c\/strong\u003e Switch off and let the heater cool (Bromic says at least 2 hours) before cleaning. Inspect and clean the body and structure at least monthly, and wipe it with a soft damp cloth every two weeks in coastal areas. Do not use steam cleaners. Have the heater inspected before use and serviced at least once a year by a qualified, licensed person.\u003c\/p\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's published warranty page does not list a separate term for suspension kits. It covers Platinum Electric heaters for 3 years, for the original owner only, from the date of purchase. Bromic supplies a replacement heater or part; the owner pays labor, shipping and other costs. Implied warranties are limited to one year, and claims start with the dealer who sold the product. Ask us to confirm the kit's coverage before you order.\u003c\/p\u003e\n\u003ch3 id=\"manuals\"\u003eManuals and documents\u003c\/h3\u003e\n\u003cul class=\"mnk-docs\"\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/Bromic-Platinum-Smart-Heat-Electric-SII-Instruction-Manual-US_v4.pdf\" target=\"_blank\" rel=\"noopener\"\u003ePlatinum Smart-Heat Electric Series II 2300W \/ 3400W manual, US version 4 (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eTube suspension kit part numbers and notes, specifications, clearances, care\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/Bromic-Platinum-Smart-Heat-Electric-SII-Instruction-Manual-4.5kW-AU-UK-US_v1.1.pdf\" target=\"_blank\" rel=\"noopener\"\u003ePlatinum Smart-Heat Electric Series II 4500W manual, version 1.3 (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eTube suspension part numbers by region, mounting heights, clearances\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/warranty\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic warranty terms\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eWarranty periods by product line\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"2300W\/3400W \/ 600 mm","offer_id":68167513964823,"sku":"BH3130023-1","price":394.0,"currency_code":"USD","in_stock":true},{"title":"2300W\/3400W \/ 1200 mm","offer_id":68167513997591,"sku":"BH3130024-1","price":523.0,"currency_code":"USD","in_stock":true},{"title":"4500W \/ 600 mm","offer_id":68167514030359,"sku":"BH3623020","price":394.0,"currency_code":"USD","in_stock":true},{"title":"4500W \/ 1200 mm","offer_id":68167514063127,"sku":"BH3623021","price":523.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-platinum-electric-tube-suspension-kit-600-mm-or-1200-bh3130023-1-bh3130024-1-bh3623020.jpg?v=1794343422"},{"product_id":"bromic-platinum-electric-marine-ceiling-recess-kit","title":"Bromic Platinum Electric Marine Ceiling Recess Kit - 2300W, 3400W or 4500W","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe Bromic Platinum Electric Marine Ceiling Recess Kit is Bromic's standard-clearance kit for flush-mounting a \u003ca href=\"\/collections\/bromic-heating\"\u003ePlatinum Smart-Heat Electric Marine heater\u003c\/a\u003e into the ceiling, so only the heater face shows. Bromic describes it as ideal for new builds that leave more cavity space above the ceiling. The kit is brushed grade 316 stainless steel, the same marine grade as the heaters, and recessed installation is approved for land-based and coastal sites only.\u003c\/p\u003e\n\u003cp\u003eChoose the kit size above to match your heater: BH3130034 for the \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-2300w-patio-heater\"\u003eMarine 2300W\u003c\/a\u003e, BH3130035 for the \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-3400w-patio-heater\"\u003eMarine 3400W\u003c\/a\u003e or BH3623001 for the \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-4500w-patio-heater\"\u003eMarine 4500W\u003c\/a\u003e. The heater is not included. For grade 304 Platinum Electric heaters, see the \u003ca href=\"\/products\/bromic-platinum-electric-ceiling-recess-kit\"\u003estandard Ceiling Recess Kit\u003c\/a\u003e. Where the ceiling cavity is shallow, the \u003ca href=\"\/products\/bromic-platinum-electric-marine-low-clearance-recess-kit\"\u003eMarine Low Clearance Recess Kit\u003c\/a\u003e works in as little as 7.1 in. of vertical space and adds its own cooling fan.\u003c\/p\u003e\n\u003cp\u003ePlan before ordering: the ceiling lining must be 10 to 30 mm (0.4 to 1.2 in.) thick, the heater face must sit at least 2400 mm (94 in.) above the floor, and joists, beams and rafters must not be cut. The cavity needs the clearances to combustibles shown in Bromic's manual, the heater must never be covered with insulation, and it must be fully protected from water above. A licensed electrician installs and hard-wires it.\u003c\/p\u003e\n\u003cul class=\"mnk-glance\"\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFits:\u003c\/strong\u003e Platinum Electric Marine 2300W, 3400W, 4500W\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eMaterial:\u003c\/strong\u003e Brushed stainless steel, grade 316\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eCeiling thickness:\u003c\/strong\u003e 0.4 to 1.2 in.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eHeater height:\u003c\/strong\u003e 94 in. minimum above the floor\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eUse:\u003c\/strong\u003e Land-based and coastal sites\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"features\"\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFlush ceiling finish:\u003c\/strong\u003e the heater sits up in the recess frame, so only its face shows below the ceiling line.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrade 316 marine stainless:\u003c\/strong\u003e matches the Platinum Electric Marine heaters for coastal air and salt spray.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSized to each heater:\u003c\/strong\u003e separate kits for the 2300W, 3400W and 4500W Marine heaters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorks with standard ceiling linings:\u003c\/strong\u003e 10 to 30 mm (0.4 to 1.2 in.) thick; Bromic advises on thicker ceilings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUses the heater's own bracket:\u003c\/strong\u003e the heater bracket hooks into the recess mounting plate, and the power cable enters through an extra cable gland.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eIdentification\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003ePlatinum Smart-Heat Electric, Ceiling Recess Kit (standard clearance), Marine\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart numbers\u003c\/th\u003e\n\u003ctd\u003eBH3130034 (2300W), BH3130035 (3400W), BH3623001 (4500W)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003ePlatinum Smart-Heat Electric Marine 2300W, 3400W and 4500W heaters (heater not included)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrushed stainless steel, grade 316\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eCeiling and clearances\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCeiling lining thickness\u003c\/th\u003e\n\u003ctd\u003e10 to 30 mm (0.4 to 1.2 in.); thicker ceilings: contact Bromic\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater face above floor\u003c\/th\u003e\n\u003ctd\u003e2400 mm (94 in.) minimum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eTo nearest wall\u003c\/th\u003e\n\u003ctd\u003e500 mm (20 in.) minimum, on all sides\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBetween heaters\u003c\/th\u003e\n\u003ctd\u003e500 mm (20 in.) minimum, from the heater edge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCut-out and cavity clearances\u003c\/th\u003e\n\u003ctd\u003eShown on the manual's recess diagrams; use one clearance option only, never a mix of the two\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eHeater it carries (for structural planning)\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMarine 2300W\u003c\/th\u003e\n\u003ctd\u003e840 x 182 x 54 mm (33.0 x 7.0 x 2.0 in.), 7.5 kg (16.5 lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMarine 3400W\u003c\/th\u003e\n\u003ctd\u003e1275 x 182 x 54 mm (50.2 x 7.0 x 2.0 in.), 10 kg (22 lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMarine 4500W\u003c\/th\u003e\n\u003ctd\u003e1351 x 257 x 54 mm (53.2 x 10.1 x 2.1 in.), 15 kg (33 lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eElectrical (heater)\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCurrent, 2300W\u003c\/th\u003e\n\u003ctd\u003e11.1 A at 208V; 9.6 A at 220-240V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCurrent, 3400W\u003c\/th\u003e\n\u003ctd\u003e16.3 A at 208V; 14.2 A at 220-240V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCurrent, 4500W\u003c\/th\u003e\n\u003ctd\u003e21.6 A at 208V; 18.8 A at 220-240V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eConnection\u003c\/th\u003e\n\u003ctd\u003ePermanently hard-wired and grounded, by a licensed person\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eUse\u003c\/th\u003e\n\u003ctd\u003eRecess installs: land-based and coastal sites only; never on marine craft\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003cdiv class=\"mnk-kit\"\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"whats-included\"\u003eWhat's included\u003c\/h3\u003e\n\u003cul class=\"mnk-included\"\u003e\n\u003cli\u003eCeiling recess frame and the parts and hardware for recessed mounting (Bromic product page)\u003c\/li\u003e\n\u003cli\u003eParts the manual's recess steps call for: an extra cable gland and nut, a two-piece recess mounting plate, a bracket end-cap with four M5 screws and nuts, a straight cover and a larger cover, M6 x 14 mm mounting screws and M4 x 10 mm positioning screws\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBromic does not publish a separate packing list. Not included: the heater and the fasteners into the ceiling structure.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"sold-separately\"\u003eSold separately\u003c\/h3\u003e\n\u003cul class=\"mnk-optional\"\u003e\n\u003cli\u003eHeaters: \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-2300w-patio-heater\"\u003ePlatinum Electric Marine 2300W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-3400w-patio-heater\"\u003e3400W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-4500w-patio-heater\"\u003e4500W\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eControls: \u003ca href=\"\/products\/bromic-affinity-smart-heat-on-off-controller\"\u003eAffinity Smart-Heat On\/Off\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-affinity-smart-heat-dimmer-controller\"\u003eAffinity Smart-Heat Dimmer\u003c\/a\u003e or the \u003ca href=\"\/products\/bromic-manual-wall-switch-heater-kit\"\u003eBromic manual wall switch kit\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eFor shallow cavities: \u003ca href=\"\/products\/bromic-platinum-electric-marine-low-clearance-recess-kit\"\u003eMarine Low Clearance Recess Kit\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003ch3 id=\"installation\"\u003eInstallation planning\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstaller:\u003c\/strong\u003e a licensed, authorized person, to local electrical codes. The heater is permanently hard-wired to a supply that matches its rating label and is properly grounded. Bromic's manual calls for an RCD or RCCB and a bipolar circuit breaker with at least 3 mm contact opening on direct supply connections. Switch off the power before installation or maintenance.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStructure:\u003c\/strong\u003e do not cut or notch joists, beams or rafters. Fix the frame into material strong enough to carry the heater (reinforcement may be needed). The locator hole used depends on the ceiling thickness.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCavity:\u003c\/strong\u003e keep the clearances to combustibles shown in the manual's recess diagrams. They are fixed minimums for each of the two options and cannot be combined. Never cover the heater with insulation or similar material, and protect it fully from water from above.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBromic's supplementary cavity requirements (2300W and 3400W, US 1.0):\u003c\/strong\u003e structural members no larger than 2 x 6 in., joists at least 16 in. on center, at least 4 in. between fire-protected members and the ceiling, at least one layer of 5\/8 in. fire board on the first row of timber members beside the heater, spacers between the kit and the fire board, and support along the short side of the kit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeight and spacing:\u003c\/strong\u003e heater face at least 2400 mm (94 in.) above the floor, at least 500 mm (20 in.) from the nearest wall on all sides and at least 500 mm (20 in.) between heaters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSequence:\u003c\/strong\u003e cut the opening to the manual's cut-out drawing, fit the recess frame, swap the heater's plug-in wall bracket for the extra cable gland, fit the bracket covers and end-cap, add the two-piece mounting plate, make the electrical connection, then raise the heater into the cavity, rotate it level and lower it onto the frame.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMarine:\u003c\/strong\u003e IPX5 protection on a marine heater depends on sealed mounting and IP55-rated electrical components. Recess installation is for land and coastal use only; never install a marine heater on a boat.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCare:\u003c\/strong\u003e Switch off and let the heater cool (Bromic says at least 2 hours) before cleaning. Inspect and clean the body and structure at least monthly, and more often in coastal or other harsh conditions. Remove salt spray straight away, and have a qualified technician check for corrosion; take the heater out of service if safety is affected. Only an authorized, licensed service person may service or repair it.\u003c\/p\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's published warranty page does not list a separate term for recess kits. It covers Platinum Electric Marine heaters for 5 years on land-based installations (3 years on marine vessels), for the original owner only, from the date of purchase. Bromic supplies a replacement heater or part; the owner pays service, removal and reinstallation labor, shipping and other costs. Implied warranties are limited to one year. Claims start with the dealer who sold the product. Ask us to confirm the kit's coverage before you order.\u003c\/p\u003e\n\u003ch3 id=\"manuals\"\u003eManuals and documents\u003c\/h3\u003e\n\u003cul class=\"mnk-docs\"\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/Bromic-Platinum-Smart-Heat-Electric-SII-Instruction-Manual-US_v4.pdf\" target=\"_blank\" rel=\"noopener\"\u003ePlatinum Smart-Heat Electric Series II 2300W \/ 3400W manual, US version 4 (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eRecess kit part numbers (p. 9), recess steps and cut-out drawing (pp. 10-11), specifications (p. 5), care\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/Bromic-Platinum-Smart-Heat-Electric-SII-Instruction-Manual-4.5kW-AU-UK-US_v1.1.pdf\" target=\"_blank\" rel=\"noopener\"\u003ePlatinum Smart-Heat Electric Series II 4500W manual, version 1.3 (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003e4500W recess kit part numbers, cut-out, clearances, specifications\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/product\/platinum-electric-recess-kit\" target=\"_blank\" rel=\"noopener\"\u003eBromic Platinum Electric Recess Kits product page\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eSizes and compatibility\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/warranty\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic warranty terms\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eWarranty periods by product line\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBromic's Supplementary Recess Kit Cavity Requirements (US 1.0, 2300W and 3400W) is available on request.\u003c\/p\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"2300W","offer_id":68167514128663,"sku":"BH3130034","price":851.0,"currency_code":"USD","in_stock":true},{"title":"3400W","offer_id":68167514161431,"sku":"BH3130035","price":1015.0,"currency_code":"USD","in_stock":true},{"title":"4500W","offer_id":68167514194199,"sku":"BH3623001","price":1167.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-platinum-electric-marine-ceiling-recess-kit-2300w-bh3130034-bh3130035-bh3623001-recess.jpg?v=1794343282"},{"product_id":"bromic-platinum-electric-marine-low-clearance-recess-kit","title":"Bromic Platinum Electric Marine Low Clearance Ceiling Recess Kit - 2300W, 3400W or 4500W","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe Bromic Platinum Electric Marine Low Clearance Ceiling Recess Kit flush-mounts a \u003ca href=\"\/collections\/bromic-heating\"\u003ePlatinum Smart-Heat Electric Marine heater\u003c\/a\u003e into a ceiling cavity with as little as 7.1 in. of vertical space. The recess box fits within standard ceiling joists, and a built-in frame and integrated cooling fan manage temperature in the cavity, so recessed heat is possible in a new build or a retrofit where a standard recess kit would not fit. Bromic describes the Low Clearance kit as UL certified.\u003c\/p\u003e\n\u003cp\u003eChoose the kit size above to match your heater: 2300W (BH3623011), 3400W (BH3623010-1) or 4500W (BH3623013-1), to suit the \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-2300w-patio-heater\"\u003eMarine 2300W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-3400w-patio-heater\"\u003eMarine 3400W\u003c\/a\u003e or \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-4500w-patio-heater\"\u003eMarine 4500W\u003c\/a\u003e heater. The marine kit is brushed grade 316 stainless steel and comes with both black and white vent covers so they can match the heater color. The heater itself is not included. For standard (grade 304) Platinum Electric heaters, see the \u003ca href=\"\/products\/bromic-platinum-electric-low-clearance-recess-kit\"\u003estandard Low Clearance kit\u003c\/a\u003e; Bromic also makes a standard-clearance \u003ca href=\"\/products\/bromic-platinum-electric-marine-ceiling-recess-kit\"\u003eMarine Ceiling Recess Kit\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003ePlan before ordering: the integrated fan needs its own constant power supply that is live at all times (not after a switch) and runs independently of the heater. The ceiling cut-out must sit between joists without cutting them, the heater face must be at least 2400 mm above the finished floor, and installation is by a licensed technician with two people. Marine versions are for land-based and coastal sites, not for boats.\u003c\/p\u003e\n\u003cul class=\"mnk-glance\"\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eCavity depth:\u003c\/strong\u003e 7.1 in. minimum\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eSizes:\u003c\/strong\u003e 2300W, 3400W, 4500W heaters\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eMaterial:\u003c\/strong\u003e Grade 316 stainless steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFan supply:\u003c\/strong\u003e 100-127V, 208V or 220-240V, under 1 A\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eCeiling thickness:\u003c\/strong\u003e 0.39 to 1.18 in.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"features\"\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e7.1 in. cavity:\u003c\/strong\u003e flush-mounts the heater where ceiling space is shallow, within standard joist spacing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIntegrated cooling fan and frame:\u003c\/strong\u003e keep the recess cavity within temperature limits, on a dedicated always-on supply.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrade 316 marine stainless:\u003c\/strong\u003e made for coastal sites, matching the Platinum Electric Marine heaters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBlack and white vent covers included:\u003c\/strong\u003e fit the set that matches your heater for a flush, finished ceiling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eComplete recess hardware:\u003c\/strong\u003e recess box, IP cover, terminal box, trims and screws are in the box; ceiling fasteners are supplied by the installer.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThermal protection:\u003c\/strong\u003e a self-resetting thermal switch must be plugged in for the heater to run, and a manual-reset thermal switch in the terminal box trips on over-temperature.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eIdentification\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003ePlatinum Smart-Heat Electric, Low Clearance (LC) Ceiling Recess Kit, Marine\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart numbers\u003c\/th\u003e\n\u003ctd\u003eBH3623011 (2300W; BH3623011-1 in the REV10 manual), BH3623010-1 (3400W), BH3623013-1 (4500W)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003ePlatinum Smart-Heat Electric Marine 2300W, 3400W and 4500W heaters (heater not included)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eCeiling cut-out\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e2300W\u003c\/th\u003e\n\u003ctd\u003e995 x 240 mm (39.2 x 9.4 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e3400W\u003c\/th\u003e\n\u003ctd\u003e1430 x 240 mm (56.3 x 9.4 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e4500W\u003c\/th\u003e\n\u003ctd\u003e1550 x 317 mm (61.0 x 12.5 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eKit size (L x W x H)\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e2300W\u003c\/th\u003e\n\u003ctd\u003e1039 x 261 x 175 mm (40.9 x 10.3 x 6.9 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e3400W\u003c\/th\u003e\n\u003ctd\u003e1475 x 261 x 175 mm (58.1 x 10.3 x 6.9 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e4500W\u003c\/th\u003e\n\u003ctd\u003e1595 x 338 x 178 mm (62.8 x 13.3 x 7.0 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eInstalled weight with heater (structural planning)\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e2300W\u003c\/th\u003e\n\u003ctd\u003e18.5 kg (41 lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e3400W\u003c\/th\u003e\n\u003ctd\u003e24 kg (53 lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eClearances\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eVertical space above ceiling\u003c\/th\u003e\n\u003ctd\u003e180 mm (7.1 in.) minimum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eTerminal box end to nearest surface\u003c\/th\u003e\n\u003ctd\u003e200 mm (7.9 in.) minimum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCut-out to nearest wall\u003c\/th\u003e\n\u003ctd\u003e500 mm (19.7 in.) minimum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBetween heaters\u003c\/th\u003e\n\u003ctd\u003e500 mm (19.7 in.) minimum, from cut-out edge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater surface to finished floor\u003c\/th\u003e\n\u003ctd\u003e2400 mm minimum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSpace between joists\u003c\/th\u003e\n\u003ctd\u003e240 mm (9.4 in.) for 2300W and 3400W; 317 mm (12.5 in.) for 4500W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eBuild and electrical\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrushed stainless steel, grade 316\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCeiling thickness\u003c\/th\u003e\n\u003ctd\u003e10 to 30 mm (0.39 to 1.18 in.); thicker ceilings: contact Bromic\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFan supply\u003c\/th\u003e\n\u003ctd\u003e100-127V AC 50\/60 Hz, 208V AC 60 Hz or 220-240V AC 50\/60 Hz; under 1.0 A; constant, unswitched\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eTerminal wire size\u003c\/th\u003e\n\u003ctd\u003e10 AWG (6.0 mm²) maximum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eOutdoor wiring parts\u003c\/th\u003e\n\u003ctd\u003eIPX5 or better\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCertification\u003c\/th\u003e\n\u003ctd\u003eUL certified (Bromic product page)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eUse\u003c\/th\u003e\n\u003ctd\u003eLand-based and coastal installations; not for marine craft\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003cdiv class=\"mnk-kit\"\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"whats-included\"\u003eWhat's included\u003c\/h3\u003e\n\u003cul class=\"mnk-included\"\u003e\n\u003cli\u003eCeiling recess box with integrated cooling fan\u003c\/li\u003e\n\u003cli\u003eIP cover and terminal box\u003c\/li\u003e\n\u003cli\u003eBlack and white vent covers, with vent cover trims\u003c\/li\u003e\n\u003cli\u003eMarine trim assembly\u003c\/li\u003e\n\u003cli\u003eScrews: 8 x M3x6, 8 x M4x8, 1 x M6x10 and M5x12 hex flange bolts\u003c\/li\u003e\n\u003cli\u003e3-way WAGO connectors (4500W kit only)\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot included: the heater and the fasteners into the ceiling structure.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"sold-separately\"\u003eSold separately\u003c\/h3\u003e\n\u003cul class=\"mnk-optional\"\u003e\n\u003cli\u003eHeaters: \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-2300w-patio-heater\"\u003ePlatinum Electric Marine 2300W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-3400w-patio-heater\"\u003e3400W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-4500w-patio-heater\"\u003e4500W\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eControls shown in the wiring diagrams: \u003ca href=\"\/products\/bromic-affinity-smart-heat-dimmer-controller\"\u003eAffinity Smart-Heat Dimmer\u003c\/a\u003e (1 channel), \u003ca href=\"\/products\/bromic-affinity-smart-heat-on-off-controller\"\u003eAffinity Smart-Heat On\/Off\u003c\/a\u003e (2 channel, for separate element control on the 4500W), or a wall switch such as the \u003ca href=\"\/products\/bromic-manual-wall-switch-heater-kit\"\u003eBromic manual wall switch kit\u003c\/a\u003e; Bromic recommends two 20 A switches for the 4500W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003ch3 id=\"installation\"\u003eInstallation planning\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstaller:\u003c\/strong\u003e a licensed, authorized person, to local electrical codes. Disconnect power during installation and maintenance. At least two people are needed for the lifting steps (16 kg, about 35 lb, maximum safe lift per person).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStructure:\u003c\/strong\u003e do not cut or notch joists, beams or rafters. Fix the recess box with at least 6 suitable fasteners along the long edge (at least 10 into timber members), into material that can carry the assembly; reinforcement may be needed, and the installer confirms the structure can carry the load.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCavity:\u003c\/strong\u003e at least 180 mm (7.1 in.) of vertical space, 200 mm (7.9 in.) at the terminal box end and 500 mm (19.7 in.) from the cut-out to the nearest wall. Never cover the kit or heater with insulation or similar material, and protect it fully from water from above.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeight and spacing:\u003c\/strong\u003e heater surface at least 2400 mm above the finished floor, and at least 500 mm between heaters from the cut-out edge.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFan wiring:\u003c\/strong\u003e the fan supply must be constant and live at all times, not after a switch, so the fan runs independently of the heater. Use outdoor wiring parts rated IPX5 or better; terminals take up to 10 AWG. The 4500W kit can take separate supplies to control each element.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThermal switch:\u003c\/strong\u003e plug the self-resetting thermal switch into the terminal box receptacle, or the heater will not run.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMarine use:\u003c\/strong\u003e for land-based and coastal sites only; the marine version must not be installed on marine craft.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCare:\u003c\/strong\u003e Switch off and wait at least 2 hours before cleaning. Clean the exterior every two weeks with a soft, damp cloth, more often in harsh conditions; rinse off salt spray straight away, and have a qualified technician check for corrosion every year, removing the unit from service if safety is affected. Only an authorized, licensed service person may service it; do not run a malfunctioning heater. If the manual-reset thermal switch in the terminal box trips (often a fan fault or high ambient temperature), reset it by pressing its center button only with the circuit de-energized.\u003c\/p\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's published warranty page does not list a separate term for recess kits. It covers Platinum Electric Marine heaters for 5 years on land-based installations, for the original owner, with Bromic supplying a replacement heater or part and the owner paying labor, shipping and installation costs. Ask us to confirm the kit's coverage before you order.\u003c\/p\u003e\n\u003ch3 id=\"manuals\"\u003eManuals and documents\u003c\/h3\u003e\n\u003cul class=\"mnk-docs\"\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2025\/12\/Bromic-Platinum-Electric-Low-Clearance-Recess-Kit-Manual-EN.pdf\" target=\"_blank\" rel=\"noopener\"\u003ePlatinum Smart-Heat Electric Low Clearance Ceiling Recess installation instructions, REV10 (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003ePart numbers, cut-outs, clearances, structure, wiring, care\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2025\/05\/LCRK-Affinity-Wiring-Guide-NA.pdf\" target=\"_blank\" rel=\"noopener\"\u003eLCRK Affinity wiring guide, North America (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eFan, heater and Affinity 1 channel wiring, earlier control box revision\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/product\/platinum-electric-low-clearance-recess-kit\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic Platinum Electric Low-Clearance Recess Kit product page\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eSizes, compatibility, installation video\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/warranty\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic warranty terms\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eWarranty periods by product line\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"2300W","offer_id":68167514292503,"sku":"BH3623011","price":1724.0,"currency_code":"USD","in_stock":true},{"title":"3400W","offer_id":68167514325271,"sku":"BH3623010-1","price":1898.0,"currency_code":"USD","in_stock":true},{"title":"4500W","offer_id":68167514358039,"sku":"BH3623013-1","price":2816.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-platinum-electric-marine-low-clearance-ceiling-bh3623011-bh3623010-1-bh3623013-1-recess.jpg?v=1794343282"},{"product_id":"bromic-platinum-electric-marine-tube-suspension-kit","title":"Bromic Platinum Electric Marine Tube Suspension Kit - 600 mm or 1200 mm","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe Bromic Platinum Electric Marine Tube Suspension Kit is a brushed grade 316 stainless steel ceiling pole that hangs a \u003ca href=\"\/collections\/bromic-heating\"\u003ePlatinum Smart-Heat Electric Marine heater\u003c\/a\u003e below a high ceiling, bringing the heat down toward the seating area. Bromic makes it in two lengths, 600 mm (23.62 in.) and 1200 mm (47.24 in.), and in the same marine-grade 316 stainless steel as the \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-2300w-patio-heater\"\u003eMarine 2300W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-3400w-patio-heater\"\u003eMarine 3400W\u003c\/a\u003e and \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-4500w-patio-heater\"\u003eMarine 4500W\u003c\/a\u003e heaters.\u003c\/p\u003e\n\u003cp\u003eChoose the heater size and pole length above. Bromic's manuals list BH3130046 (600 mm) and BH3130047 (1200 mm) as the US marine tube suspension kits, for the 2300W and 3400W heaters and also in the 4500W manual's North America column. We also list 4500W options under BH3623022 and BH3623023; those part numbers do not appear in Bromic's manuals, so ask us to confirm the right kit for a 4500W heater before you order.\u003c\/p\u003e\n\u003cp\u003ePlan before ordering: the pole is for ceiling mounting only and must never be wall-mounted. It is used with a ceiling bracket, sold separately, in place of the mounting bracket that comes with the heater. The heater itself is not included, and a licensed electrician installs and hard-wires it.\u003c\/p\u003e\n\u003cul class=\"mnk-glance\"\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eLengths:\u003c\/strong\u003e 600 mm (23.62 in.) or 1200 mm (47.24 in.)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eMaterial:\u003c\/strong\u003e Brushed stainless steel, grade 316\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eMounting:\u003c\/strong\u003e Ceiling only\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFits:\u003c\/strong\u003e Platinum Electric Marine heaters\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"features\"\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo drop lengths:\u003c\/strong\u003e 600 mm (23.62 in.) or 1200 mm (47.24 in.), to bring a heater down from a high ceiling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrade 316 marine stainless:\u003c\/strong\u003e matches the Platinum Electric Marine heaters for coastal air and salt spray.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCeiling-only design:\u003c\/strong\u003e the pole hangs the heater from above; Bromic does not allow wall mounting with it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrade 304 version for standard heaters:\u003c\/strong\u003e non-marine Platinum Electric heaters use the \u003ca href=\"\/products\/bromic-platinum-electric-tube-suspension-kit\"\u003ePlatinum Electric Tube Suspension Kit\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eIdentification\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003ePlatinum Smart-Heat Electric, Tube Suspension Kit, Marine\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart numbers (Bromic manuals)\u003c\/th\u003e\n\u003ctd\u003eBH3130046 (600 mm), BH3130047 (1200 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eOur 4500W options\u003c\/th\u003e\n\u003ctd\u003eBH3623022 (600 mm), BH3623023 (1200 mm); ask us to confirm fit\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003ePlatinum Smart-Heat Electric Marine heaters (heater not included)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eBuild\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLength\u003c\/th\u003e\n\u003ctd\u003e600 mm (23.62 in.) or 1200 mm (47.24 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eBrushed stainless steel, grade 316\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMounting\u003c\/th\u003e\n\u003ctd\u003eCeiling only; do not wall-mount\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBracket\u003c\/th\u003e\n\u003ctd\u003eCeiling bracket, sold separately, replaces the heater's supplied mounting bracket\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eHeater it carries\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMarine 2300W\u003c\/th\u003e\n\u003ctd\u003e840 x 182 x 54 mm (33.0 x 7.0 x 2.0 in.), 7.5 kg (16.5 lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMarine 3400W\u003c\/th\u003e\n\u003ctd\u003e1275 x 182 x 54 mm (50.2 x 7.0 x 2.0 in.), 10 kg (22 lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMarine 4500W\u003c\/th\u003e\n\u003ctd\u003e1351 x 257 x 54 mm (53.2 x 10.1 x 2.1 in.), 15 kg (33 lb)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBetween heaters\u003c\/th\u003e\n\u003ctd\u003e500 mm (20 in.) minimum, from the heater edge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eUse\u003c\/th\u003e\n\u003ctd\u003eLand-based and coastal sites; marine heaters must not be installed on marine craft\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003cdiv class=\"mnk-kit\"\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"whats-included\"\u003eWhat's included\u003c\/h3\u003e\n\u003cul class=\"mnk-included\"\u003e\n\u003cli\u003eBrushed grade 316 stainless steel suspension pole, 600 mm or 1200 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBromic does not publish a packing list for this kit. Not included: the heater, the ceiling bracket and the fasteners into the ceiling structure.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"sold-separately\"\u003eSold separately\u003c\/h3\u003e\n\u003cul class=\"mnk-optional\"\u003e\n\u003cli\u003eHeaters: \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-2300w-patio-heater\"\u003ePlatinum Electric Marine 2300W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-3400w-patio-heater\"\u003e3400W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-smart-heat-electric-marine-4500w-patio-heater\"\u003e4500W\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eCeiling bracket for tube suspension (Bromic; ask us)\u003c\/li\u003e\n\u003cli\u003eControls: \u003ca href=\"\/products\/bromic-affinity-smart-heat-on-off-controller\"\u003eAffinity Smart-Heat On\/Off\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-affinity-smart-heat-dimmer-controller\"\u003eAffinity Smart-Heat Dimmer\u003c\/a\u003e or the \u003ca href=\"\/products\/bromic-manual-wall-switch-heater-kit\"\u003eBromic manual wall switch kit\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eFlush-mount alternatives: \u003ca href=\"\/products\/bromic-platinum-electric-marine-ceiling-recess-kit\"\u003eMarine Ceiling Recess Kit\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-platinum-electric-marine-low-clearance-recess-kit\"\u003eMarine Low Clearance Recess Kit\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003ch3 id=\"installation\"\u003eInstallation planning\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstaller:\u003c\/strong\u003e the heater must be permanently installed and hard-wired by a licensed, authorized person to local electrical codes, on a grounded supply that matches its rating label. Switch off the power before installation or maintenance.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e ceiling only, using the separately sold ceiling bracket instead of the bracket supplied with the heater. Fix into structure strong enough to carry the heater and pole.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeight and spacing:\u003c\/strong\u003e Bromic's ceiling-mounting minimum is 2400 mm (96 in.) above the floor, so choose a pole length that keeps the heater above that. Keep at least 500 mm (20 in.) between heaters, measured from the heater edge, and follow the clearances to combustibles in the heater manual.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMarine:\u003c\/strong\u003e for land-based and coastal sites; marine heaters must not be installed on marine craft.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCare:\u003c\/strong\u003e Switch off and let the heater cool (Bromic says at least 2 hours) before cleaning. Inspect and clean the body and structure at least monthly, more often near the coast. Remove salt spray straight away, and have a qualified technician check for corrosion. Only an authorized, licensed service person may service or repair the heater.\u003c\/p\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's published warranty page does not list a separate term for suspension kits. It covers Platinum Electric Marine heaters for 5 years on land-based installations (3 years on marine vessels), for the original owner only, from the date of purchase. Bromic supplies a replacement heater or part; the owner pays labor, shipping and other costs. Implied warranties are limited to one year. Ask us to confirm the kit's coverage before you order.\u003c\/p\u003e\n\u003ch3 id=\"manuals\"\u003eManuals and documents\u003c\/h3\u003e\n\u003cul class=\"mnk-docs\"\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/Bromic-Platinum-Smart-Heat-Electric-SII-Instruction-Manual-US_v4.pdf\" target=\"_blank\" rel=\"noopener\"\u003ePlatinum Smart-Heat Electric Series II 2300W \/ 3400W manual, US version 4 (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eTube suspension kit part numbers and notes (p. 11), specifications (p. 5), care\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/Bromic-Platinum-Smart-Heat-Electric-SII-Instruction-Manual-4.5kW-AU-UK-US_v1.1.pdf\" target=\"_blank\" rel=\"noopener\"\u003ePlatinum Smart-Heat Electric Series II 4500W manual, version 1.3 (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eTube suspension part numbers by region, mounting heights, clearances\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/warranty\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic warranty terms\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eWarranty periods by product line\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"2300W\/3400W \/ 600 mm","offer_id":68167514423575,"sku":"BH3130046","price":632.0,"currency_code":"USD","in_stock":true},{"title":"2300W\/3400W \/ 1200 mm","offer_id":68167514456343,"sku":"BH3130047","price":818.0,"currency_code":"USD","in_stock":true},{"title":"4500W \/ 600 mm","offer_id":68167514489111,"sku":"BH3623022","price":632.0,"currency_code":"USD","in_stock":true},{"title":"4500W \/ 1200 mm","offer_id":68167514521879,"sku":"BH3623023","price":818.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-platinum-electric-marine-tube-suspension-kit-600-mm-bh3130046-bh3130047-bh3623022-and.jpg?v=1794343422"},{"product_id":"bromic-tungsten-electric-ceiling-recess-kit","title":"Bromic Tungsten Electric Ceiling Recess Kit - Black or White","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe Bromic Tungsten Electric Ceiling Recess Kit lets you mount a \u003ca href=\"\/collections\/bromic-heating\"\u003eTungsten Smart-Heat Electric heater\u003c\/a\u003e flush in a ceiling, so only the heater face shows below the ceiling line. The kit is the ceiling frame, the mounting brackets that hook the heater onto it, and the wiring parts for the connection; the ceiling box itself is built on site by your installer from cement board or a similar material.\u003c\/p\u003e\n\u003cp\u003eTwo sizes follow the heater length: one kit fits the 44 in. \u003ca href=\"\/products\/bromic-tungsten-smart-heat-electric-2000w-patio-heater\"\u003eTungsten Electric 2000W\u003c\/a\u003e and \u003ca href=\"\/products\/bromic-tungsten-smart-heat-electric-4000w-patio-heater\"\u003e4000W\u003c\/a\u003e, the other fits the 56 in. \u003ca href=\"\/products\/bromic-tungsten-smart-heat-electric-3000w-patio-heater\"\u003e3000W\u003c\/a\u003e and \u003ca href=\"\/products\/bromic-tungsten-smart-heat-electric-6000w-patio-heater\"\u003e6000W\u003c\/a\u003e. Choose black or white above to match the heater. The heater is not included.\u003c\/p\u003e\n\u003cp\u003ePlan before ordering: the ceiling box must be at least 46 in. long for the 2000W\/4000W kit or 57.5 in. for the 3000W\/6000W kit, the heater face must sit at least 96 in. (8 ft) above the floor, and the electrical connection is made outside the ceiling box by a licensed electrician. For a surface-mounted ceiling install instead, see the \u003ca href=\"\/products\/bromic-tungsten-electric-tube-suspension-kit\"\u003eTungsten Electric tube suspension kit\u003c\/a\u003e.\u003c\/p\u003e\n\u003cul class=\"mnk-glance\"\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFits:\u003c\/strong\u003e Tungsten Electric 2000W\/4000W or 3000W\/6000W\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eCeiling box length:\u003c\/strong\u003e 46 in. or 57.5 in. minimum\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFinish:\u003c\/strong\u003e Black or white\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eMounting height:\u003c\/strong\u003e 96 in. minimum to heater face\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"features\"\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFlush ceiling finish:\u003c\/strong\u003e the heater sits up in the ceiling box on a frame, for a clean line under a patio roof or pergola ceiling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHook-on mounting:\u003c\/strong\u003e brackets on both heater ends hook over the ceiling frame, so the heater lifts in, rotates level and drops into place.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo sizes:\u003c\/strong\u003e one kit for the 44 in. 2000W and 4000W heaters, one for the 56 in. 3000W and 6000W heaters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBlack or white:\u003c\/strong\u003e matches the Tungsten Electric heater finishes.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWiring parts in the box:\u003c\/strong\u003e terminal blocks, wire conduit, junction box cover and 5 wires, so dual-element heaters can be wired to run each element on its own or together.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eIdentification\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eTungsten Smart-Heat Electric, Ceiling Recess Kit\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e2000W and 4000W kit\u003c\/th\u003e\n\u003ctd\u003eBH8180010 black; white BH8180096 (manual) \/ BH8180096-2 (our SKU)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e3000W and 6000W kit\u003c\/th\u003e\n\u003ctd\u003eBH8180011 black; white BH8180095 (manual) \/ BH8180095-2 (our SKU)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eCeiling box (built by installer)\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMinimum length, 2000W and 4000W\u003c\/th\u003e\n\u003ctd\u003e46 in.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMinimum length, 3000W and 6000W\u003c\/th\u003e\n\u003ctd\u003e57.5 in.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBox material\u003c\/th\u003e\n\u003ctd\u003eCement board, Hardie board or similar\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eHeaters it fits\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e2000W and 4000W heater size\u003c\/th\u003e\n\u003ctd\u003e44 x 8.5 x 3.5 in., 19.8 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e3000W and 6000W heater size\u003c\/th\u003e\n\u003ctd\u003e56 x 8.5 x 3.5 in., 22 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater water rating\u003c\/th\u003e\n\u003ctd\u003eIPX4\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater certification\u003c\/th\u003e\n\u003ctd\u003eIntertek ETL \/ cETL\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eClearances\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater face to floor\u003c\/th\u003e\n\u003ctd\u003e96 in. (8 ft) minimum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBetween heaters\u003c\/th\u003e\n\u003ctd\u003e20 in. minimum, from heater edge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eIn front of heater\u003c\/th\u003e\n\u003ctd\u003e3 ft (900 mm) clear of furniture, curtains and other combustibles\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eWiring\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSupply wire\u003c\/th\u003e\n\u003ctd\u003eCopper or aluminum, rated 90°C minimum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCord grip and outdoor fittings\u003c\/th\u003e\n\u003ctd\u003eIPX4 rated; cord grip rated 90°C minimum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eWire nuts\u003c\/th\u003e\n\u003ctd\u003eCeramic or high-heat tolerant recommended\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003cdiv class=\"mnk-kit\"\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"whats-included\"\u003eWhat's included\u003c\/h3\u003e\n\u003cul class=\"mnk-included\"\u003e\n\u003cli\u003eCeiling frame\u003c\/li\u003e\n\u003cli\u003eMounting brackets for both heater ends, with fasteners\u003c\/li\u003e\n\u003cli\u003eTerminal blocks, wire conduit and junction box cover\u003c\/li\u003e\n\u003cli\u003e5 wires (not all are needed for every installation)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot included: the heater, the ceiling box and the fasteners that hold the frame to the box.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"sold-separately\"\u003eSold separately\u003c\/h3\u003e\n\u003cul class=\"mnk-optional\"\u003e\n\u003cli\u003eHeaters: \u003ca href=\"\/products\/bromic-tungsten-smart-heat-electric-2000w-patio-heater\"\u003eTungsten Electric 2000W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-tungsten-smart-heat-electric-3000w-patio-heater\"\u003e3000W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-tungsten-smart-heat-electric-4000w-patio-heater\"\u003e4000W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-tungsten-smart-heat-electric-6000w-patio-heater\"\u003e6000W\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eControls: \u003ca href=\"\/products\/bromic-affinity-smart-heat-on-off-controller\"\u003eAffinity Smart-Heat On\/Off\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-affinity-smart-heat-dimmer-controller\"\u003eAffinity Smart-Heat Dimmer\u003c\/a\u003e or the \u003ca href=\"\/products\/bromic-manual-wall-switch-heater-kit\"\u003emanual wall switch kit\u003c\/a\u003e; the 4000W and 6000W can use two 20 A switches for separate element control\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003ch3 id=\"installation\"\u003eInstallation planning\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstaller:\u003c\/strong\u003e a licensed, authorized person hardwires the heater to local electrical, building and municipal codes. Disconnect power before installing or servicing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCeiling box:\u003c\/strong\u003e build it on site from cement board, Hardie board or similar, at least 46 in. long (2000W\/4000W) or 57.5 in. (3000W\/6000W). If the box sits above joists, Bromic recommends lining the joists with fireproof insulation. The installer protects any nearby material with low heat tolerance.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSteps:\u003c\/strong\u003e fit the ceiling frame up into the cut-out and fasten it to the box through its mounting holes (fasteners not supplied); attach a mounting bracket to each end of the heater; raise one end of the heater into the box, then the whole heater; rotate it level and lower it so all four side brackets hook over the frame, centered.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWiring:\u003c\/strong\u003e make the connection outside the ceiling box, on its side or top. 2000W and 3000W heaters need one branch circuit; dual-element 4000W and 6000W heaters can be wired with one 20 A switch or two for separate element control, or to an Affinity controller per its own manual. Use supply wire rated 90°C, an IPX4 cord grip rated 90°C, and IPX4 outdoor fittings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePlacement:\u003c\/strong\u003e heater face at least 96 in. above the floor, 20 in. between heaters, and 3 ft clear in front. Outdoors, mount under cover and protect from rain where possible. Not for bathrooms, laundries or similar indoor areas. Mounting the heater vertically voids the warranty.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCare:\u003c\/strong\u003e Inspect the heater before use and have a qualified, licensed person service it at least once a year. Clean the exterior regularly with a soft, damp cloth, every two weeks in coastal areas to limit salt rust. Turn the heater off and let it cool for at least 2 hours before wiping the reflectors and elements with a soft, dry cloth; dust on them can cause overheating. Stop using the heater if you suspect damage.\u003c\/p\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's published warranty page does not list a separate term for recess kits. It covers Tungsten Electric heaters for 2 years, with 7 years on the heating elements, for the original owner; Bromic supplies a replacement heater or part and the owner pays labor, removal, reinstallation and shipping costs. Claims start with the dealer that sold the heater. Ask us to confirm the kit's coverage before you order.\u003c\/p\u003e\n\u003ch3 id=\"manuals\"\u003eManuals and documents\u003c\/h3\u003e\n\u003cul class=\"mnk-docs\"\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/Bromic-Tungsten-Smart-Heat-Electric-Instruction-Manual-US.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTungsten Smart-Heat Electric installation, instruction and service manual, US (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eCeiling recess steps and box sizes (pp. 9-10), wiring, clearances, care, part numbers\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2025\/04\/Product-Cut-Sheet-Tungsten-Electric.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTungsten Smart-Heat Electric product cut sheet (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eHeater ratings, IPX4, ETL listing\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/product\/tungsten-electric-recess-kit\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic Tungsten Electric Recess Kit product page\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eSizes and colors\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/warranty\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic warranty terms\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eWarranty periods by product line\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"2000W\/4000W \/ Black","offer_id":68167514620183,"sku":"BH8180010","price":820.0,"currency_code":"USD","in_stock":true},{"title":"2000W\/4000W \/ White","offer_id":68167514652951,"sku":"BH8180096-2","price":916.0,"currency_code":"USD","in_stock":true},{"title":"3000W\/6000W \/ Black","offer_id":68167514685719,"sku":"BH8180011","price":905.0,"currency_code":"USD","in_stock":true},{"title":"3000W\/6000W \/ White","offer_id":68167514718487,"sku":"BH8180095-2","price":1011.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-tungsten-electric-ceiling-recess-kit-black-or-white-bh8180010-bh8180096-2-bh8180011-and.jpg?v=1794343449"},{"product_id":"bromic-tungsten-electric-tube-suspension-kit","title":"Bromic Tungsten Electric Tube Suspension Kit - 3 Ft, Black or White","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe Bromic Tungsten Electric Tube Suspension Kit hangs a Tungsten Smart-Heat Electric heater from a high ceiling on 3 ft tubes, so the radiant heat reaches the seating area below. As supplied, the tubes put the face of the heater 39.39 in. below the ceiling. They can be cut shorter, with new mounting holes drilled in each tube, to set the heater at the right height.\u003c\/p\u003e\n\u003cp\u003eOne kit fits all four sizes: the \u003ca href=\"\/products\/bromic-tungsten-smart-heat-electric-2000w-patio-heater\"\u003e2000W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-tungsten-smart-heat-electric-3000w-patio-heater\"\u003e3000W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-tungsten-smart-heat-electric-4000w-patio-heater\"\u003e4000W\u003c\/a\u003e and \u003ca href=\"\/products\/bromic-tungsten-smart-heat-electric-6000w-patio-heater\"\u003e6000W\u003c\/a\u003e. Choose black or white to match the heater; in North America, Bromic offers white heaters in 4000W and 6000W only. The heater can be angled 15, 30 or 45 degrees either way, depending on the model, and the power cord runs inside the tube.\u003c\/p\u003e\n\u003cp\u003ePlan before ordering: the heater surface must stay at least 96 in. above the floor, and the heater must never face the ceiling. Fasteners into the ceiling are not supplied. The heater is permanently installed and hard-wired by a licensed, authorized person.\u003c\/p\u003e\n\u003cul class=\"mnk-glance\"\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eLength:\u003c\/strong\u003e 3 ft; heater face 39.39 in. below ceiling as supplied\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFinish:\u003c\/strong\u003e Black or white\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFits:\u003c\/strong\u003e Tungsten Electric 2000W, 3000W, 4000W, 6000W\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eHeater height:\u003c\/strong\u003e 96 in. minimum above the floor\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"features\"\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCut to length:\u003c\/strong\u003e shorten the 3 ft tubes and drill new holes to set the heater height for your ceiling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAdjustable angle:\u003c\/strong\u003e tilt the heater 15, 30 or 45 degrees either way (varies by model), locked with a self-tapping screw.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHidden wiring:\u003c\/strong\u003e the heater's power cord feeds through the suspension tube to the ceiling supply.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOne kit, four heaters:\u003c\/strong\u003e the same kit number covers the 2000W through 6000W models.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBlack or white:\u003c\/strong\u003e matches the heater finish.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eIdentification\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eTungsten Smart-Heat Electric, Tube Suspension Kit (Mounting Poles)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart numbers\u003c\/th\u003e\n\u003ctd\u003eBH8180012 (black); BH3130006 (white, our listing)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003eTungsten Smart-Heat Electric 2000W, 3000W, 4000W, 6000W (heater not included)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eBuild and fit\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eTube length\u003c\/th\u003e\n\u003ctd\u003e3 ft; can be cut down\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater drop as supplied\u003c\/th\u003e\n\u003ctd\u003e39.39 in. from the ceiling to the heater face\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater angle\u003c\/th\u003e\n\u003ctd\u003e15, 30 or 45 degrees either way, varies by model\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFixings\u003c\/th\u003e\n\u003ctd\u003eM5 screw, spring washer and nut to the rear bracket; M5 x 1-3\/8 in. screws, spring washers and nuts to the ceiling brackets\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater bracket\u003c\/th\u003e\n\u003ctd\u003e6.5 in. (2000W, 3000W); 9.5 in. (4000W, 6000W)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eClearances\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater surface above floor\u003c\/th\u003e\n\u003ctd\u003e96 in. (8 ft) minimum\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater front to ceiling\u003c\/th\u003e\n\u003ctd\u003e9.84 in. minimum (2000W, 3000W); 13 in. (4000W, 6000W)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFront\u003c\/th\u003e\n\u003ctd\u003e3 ft (900 mm) clear of combustibles\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBetween heaters\u003c\/th\u003e\n\u003ctd\u003e20 in. minimum, from the heater edge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eHeater it carries\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e2000W \/ 4000W\u003c\/th\u003e\n\u003ctd\u003e44 x 8.5 x 3.5 in., 19.8 lb; heats up to 64 \/ 120 sq ft\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003e3000W \/ 6000W\u003c\/th\u003e\n\u003ctd\u003e56 x 8.5 x 3.5 in., 22 lb; heats up to 100 \/ 144 sq ft\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eVoltage\u003c\/th\u003e\n\u003ctd\u003e240V, 208V or 277V (North America)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eWater rating\u003c\/th\u003e\n\u003ctd\u003eIPX4\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCertification\u003c\/th\u003e\n\u003ctd\u003eIntertek ETL \/ cETL 4005951\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003cdiv class=\"mnk-kit\"\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"whats-included\"\u003eWhat's included\u003c\/h3\u003e\n\u003cul class=\"mnk-included\"\u003e\n\u003cli\u003eSuspension tubes, 3 ft, in black or white\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBromic does not publish a packing list for the kit. Not included: the heater and the fasteners into the ceiling.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"sold-separately\"\u003eSold separately\u003c\/h3\u003e\n\u003cul class=\"mnk-optional\"\u003e\n\u003cli\u003eHeaters: \u003ca href=\"\/products\/bromic-tungsten-smart-heat-electric-2000w-patio-heater\"\u003eTungsten Electric 2000W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-tungsten-smart-heat-electric-3000w-patio-heater\"\u003e3000W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-tungsten-smart-heat-electric-4000w-patio-heater\"\u003e4000W\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-tungsten-smart-heat-electric-6000w-patio-heater\"\u003e6000W\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eControls: \u003ca href=\"\/products\/bromic-affinity-smart-heat-on-off-controller\"\u003eAffinity Smart-Heat On\/Off\u003c\/a\u003e or \u003ca href=\"\/products\/bromic-affinity-smart-heat-dimmer-controller\"\u003eAffinity Smart-Heat Dimmer\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eFlush-mount alternative: \u003ca href=\"\/products\/bromic-tungsten-electric-ceiling-recess-kit\"\u003eTungsten Electric Ceiling Recess Kit\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003ch3 id=\"installation\"\u003eInstallation planning\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eMark and attach the ceiling mounting brackets (ceiling fasteners not supplied).\u003c\/li\u003e\n\u003cli\u003eSet the heater surface at least 96 in. above the floor, cutting the tubes if needed, and drill new holes in any cut tube.\u003c\/li\u003e\n\u003cli\u003eWire the junction box, then feed the power cord through the suspension tube.\u003c\/li\u003e\n\u003cli\u003eAttach the tubes to the heater's rear bracket, set the angle and lock it with a self-tapping screw.\u003c\/li\u003e\n\u003cli\u003eRaise the heater, attach the tubes to the ceiling brackets and connect the cord to the ceiling supply.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstaller and wiring:\u003c\/strong\u003e the heater must be permanently installed and hard-wired by a licensed, authorized person to the local electrical code. Use wire rated at least 90°C; the junction box takes a 1\/2 in. weatherproof conduit fitting, and the cord grip must be IPX4 rated. Incorrect cord grip installation voids the warranty.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePosition:\u003c\/strong\u003e never face the heater at the ceiling, never install it vertically (this voids the warranty) and never place it directly above or in front of a power outlet. Outdoors, angle the face down, mount it under cover and protect it from rain where possible. Not for bathrooms, laundries and similar indoor areas.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpacing:\u003c\/strong\u003e 3 ft clear in front, 20 in. between heaters and the ceiling gap above for your model.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCare:\u003c\/strong\u003e Switch off and let the heater cool for at least 2 hours before cleaning. Wipe the exterior with a soft damp cloth, every two weeks in coastal areas, and keep the reflectors and elements free of dust with a soft dry cloth. Have the heater inspected before first use and serviced at least once a year by a qualified, licensed person.\u003c\/p\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's warranty page does not list a separate term for suspension kits. It covers Tungsten Electric heaters for 2 years, and their heating elements for 7 years, for the original owner only. Bromic supplies a replacement heater or part; the owner pays labor, removal and reinstallation, shipping both ways and other costs. Implied warranties are limited to one year. Claims start with the dealer who sold the product. Ask us to confirm the kit's coverage before you order.\u003c\/p\u003e\n\u003ch3 id=\"manuals\"\u003eManuals and documents\u003c\/h3\u003e\n\u003cul class=\"mnk-docs\"\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/Bromic-Tungsten-Smart-Heat-Electric-Instruction-Manual-US.pdf\" target=\"_blank\" rel=\"noopener\"\u003eTungsten Smart-Heat Electric installation, instruction and service manual, US (PDF; 1125_v1)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eTube suspension steps, clearances, wiring, care, parts\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/product\/tungsten-electric-mounting-poles\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic Tungsten Electric Mounting Poles product page\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003e3 ft length, black or white\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/warranty\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic warranty terms\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eWarranty periods by product line\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"Black","offer_id":68167514816791,"sku":"BH8180012","price":489.0,"currency_code":"USD","in_stock":true},{"title":"White","offer_id":68167514849559,"sku":"BH3130006","price":500.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-tungsten-electric-tube-suspension-kit-3-ft-black-or-bh8180012-bh3130006-black.jpg?v=1794343343"},{"product_id":"bromic-eclipse-8-inch-straight-pole","title":"Bromic Eclipse 8 Inch Straight Pole - BH3230001","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe Bromic Eclipse 8 Inch Straight Pole (BH3230001) is the shortest Eclipse ceiling mount pole: a single straight 8 in. upright that hangs an \u003ca href=\"\/products\/bromic-eclipse-smart-heat-electric-2900w-pendant-heater\"\u003eEclipse Smart-Heat Electric 2900W heater\u003c\/a\u003e as close to the ceiling as the minimum clearances allow. It is double-coated steel in matte black to match the heater head, which is sold separately and ships with a 24 in. twin pole.\u003c\/p\u003e\n\u003cp\u003eBromic designed it for spaces where the ceiling is only a little above the minimum mounting height, so the heater sits high while still giving good heat and light coverage below. The cable runs up inside the pole into the roof cavity. The other Eclipse poles are \u003ca href=\"\/products\/bromic-eclipse-24-inch-straight-pole\"\u003e24 in. straight (BH3230002)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-twin-pole\"\u003e24 in. twin (BH3230003)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-curved-pole\"\u003e24 in. curved (BH3230004)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-48-inch-straight-pole\"\u003e48 in. straight (BH3230005)\u003c\/a\u003e and \u003ca href=\"\/products\/bromic-eclipse-wall-mount-pole\"\u003ewall mount (BH3230006)\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003ePlan before ordering: the heater head must hang level and at least 8 ft above the floor, so allow for the 8 in. pole and the 4.4 in. head when checking the ceiling height. The pendant mount roof bracket is fixed into structural supports, not ceiling panels alone, and the heater is hard-wired by a licensed electrical contractor, with two people to lift the 30 lb head.\u003c\/p\u003e\n\u003cul class=\"mnk-glance\"\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003ePart number:\u003c\/strong\u003e BH3230001\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eLength:\u003c\/strong\u003e 8 in., straight\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFits:\u003c\/strong\u003e Eclipse Smart-Heat Electric 2900W heater head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFinish:\u003c\/strong\u003e Matte black, double-coated steel\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"features\"\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eShortest Eclipse drop:\u003c\/strong\u003e an 8 in. pole keeps the heater as close to the ceiling as the 8 ft minimum height allows, for lower covered patios.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConcealed cable:\u003c\/strong\u003e the heater cable runs up inside the pole and out into the roof cavity, so no wiring shows below the ceiling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRound ceiling cap:\u003c\/strong\u003e a round cap slides over the pole and covers the roof bracket for a clean finish at the ceiling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuick head fitting:\u003c\/strong\u003e the heater bracket's two pre-fitted screws hook into a slot in the pole, then two more screws lock it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDouble-coated steel in matte black:\u003c\/strong\u003e matches the Eclipse heater head and resists corrosion.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eIdentification\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eEclipse Smart-Heat Electric accessory\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eBH3230001\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eType\u003c\/th\u003e\n\u003ctd\u003eStraight ceiling mount pole\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003eEclipse Smart-Heat Electric 2900W heater head, 240V (BH0920001-2) or 208V (BH0920003); head not included\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eBuild\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLength\u003c\/th\u003e\n\u003ctd\u003e8 in.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eDouble-coated steel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eMatte black\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCeiling fixing\u003c\/th\u003e\n\u003ctd\u003ePendant mount roof bracket, fasteners in four opposing holes into structural supports (fasteners installer supplied)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePole to bracket\u003c\/th\u003e\n\u003ctd\u003e4 x M4 x 6 mm dome head screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCap to bracket\u003c\/th\u003e\n\u003ctd\u003eRound cap, 2 x M4 x 10 mm dome head screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHead to pole\u003c\/th\u003e\n\u003ctd\u003e2 pre-fitted plus 2 extra M4 x 6 mm dome head screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eHeater it carries\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater head\u003c\/th\u003e\n\u003ctd\u003e27.6 x 27.6 x 4.4 in., 30 lb, 2900W, IP54\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeat area\u003c\/th\u003e\n\u003ctd\u003eUp to 121 sq ft (Bromic cut sheet)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMinimum height above floor\u003c\/th\u003e\n\u003ctd\u003e8 ft (96 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eClearance in front of head\u003c\/th\u003e\n\u003ctd\u003e3.3 ft to floors, furniture, plants and heat-sensitive materials\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBetween heaters\u003c\/th\u003e\n\u003ctd\u003e20 in., from the heater edge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003cdiv class=\"mnk-kit\"\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"whats-included\"\u003eWhat's included\u003c\/h3\u003e\n\u003cul class=\"mnk-included\"\u003e\n\u003cli\u003eEclipse 8 in. straight pole, BH3230001\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBromic does not publish a separate packing list for the pole. In the heater's single pole ceiling kit the manual lists the pole with six M4 x 6 mm and two M4 x 10 mm dome head screws, and the steps use a pendant mount roof bracket and round cap; ask us to confirm which of these ship with the pole before ordering. Not included: the heater head and the ceiling fasteners.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"sold-separately\"\u003eSold separately\u003c\/h3\u003e\n\u003cul class=\"mnk-optional\"\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/bromic-eclipse-smart-heat-electric-2900w-pendant-heater\"\u003eEclipse Smart-Heat Electric 2900W heater\u003c\/a\u003e, 240V (BH0920001-2) or 208V (BH0920003); ships with the 24 in. twin pole\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/bromic-affinity-smart-heat-eclipse-controller\"\u003eAffinity Smart-Heat Eclipse controller\u003c\/a\u003e, 1 or 5 channel, for heat and light control with the app\u003c\/li\u003e\n\u003cli\u003eCeiling mount pole screw set, BH8380009 (replacement fixings; ask us)\u003c\/li\u003e\n\u003cli\u003eOther poles: \u003ca href=\"\/products\/bromic-eclipse-24-inch-straight-pole\"\u003e24 in. straight (BH3230002)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-twin-pole\"\u003e24 in. twin (BH3230003)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-curved-pole\"\u003e24 in. curved (BH3230004)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-48-inch-straight-pole\"\u003e48 in. straight (BH3230005)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-wall-mount-pole\"\u003ewall mount (BH3230006)\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003ch3 id=\"installation\"\u003eInstallation planning\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstaller:\u003c\/strong\u003e a licensed electrical contractor or authorized technician, to local codes. Two people are needed; Bromic sets a safe lift of 35 lb per person, and the head weighs 30 lb. If the heater is connected directly to the supply, a bipolar circuit breaker with at least 1\/8 in. contact opening is required upstream.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRoof bracket:\u003c\/strong\u003e fasten the pendant mount roof bracket to the ceiling with bolts sized for the surface (not included) in four opposing holes, into structural supports rather than ceiling panels alone. Bromic gives no load rating for the ceiling mount, so the installer chooses fasteners for the load and checks the surface is solid.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePole and cap:\u003c\/strong\u003e attach the pole to the bracket with four M4 x 6 mm screws, then slide the round cap over the pole and fix it to the bracket with two M4 x 10 mm screws.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting the head:\u003c\/strong\u003e keep the cardboard on the head until it is mounted. Feed the cable up through the pole into the roof cavity, hook the heater bracket's two pre-fitted M4 screws into the slot in the pole, add two more M4 x 6 mm screws and tighten all four.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePosition:\u003c\/strong\u003e the head must be level (check with a spirit level), at least 8 ft above the floor, not directly above or in front of an electrical outlet, with 3.3 ft clear in front and to heat-sensitive materials in every direction, and 20 in. between heaters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeather and location:\u003c\/strong\u003e the heater is IP54; Bromic recommends a covered position out of the rain. Keep it away from pools, showers and bathtubs. It is not for vehicles or boats. Remove all packaging before switching on.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCare:\u003c\/strong\u003e Bromic asks for an inspection before use and a service at least once a year by a qualified technician. Switch off and let the heater cool for at least 2 hours before cleaning. Clean the pole and head regularly with a clean, soft, damp cloth (for the glass, a microfiber cloth with lukewarm water and mild dish soap, wiped in one direction, then air dry); do not spray it with water or use harsh pads or chemicals. Near the coast, clean every two weeks, because salt air can cause rust.\u003c\/p\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's warranty page does not list a separate term for the Eclipse poles. The Eclipse Pendant heater is covered for 3 years, for the original owner only: Bromic supplies a replacement heater or part, and the owner pays labor, removal and reinstallation, shipping both ways and other costs. Implied warranties are limited to one year. Claims start with the dealer who sold the product. Ask us to confirm the pole's coverage before you order.\u003c\/p\u003e\n\u003ch3 id=\"manuals\"\u003eManuals and documents\u003c\/h3\u003e\n\u003cul class=\"mnk-docs\"\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/BMC-00693-Bromic-Eclipse-Electric-Pendant-Instruction-Manual-US_REV2_20250328.pdf\" target=\"_blank\" rel=\"noopener\"\u003eEclipse Smart-Heat Electric pendant instruction manual, Version 2 US, BMC-00693 (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003ePole part numbers, single pole ceiling steps, kit contents, clearances, care, spare parts\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2026\/01\/Product-Cut-Sheet-Eclipse-Electric.pdf\" target=\"_blank\" rel=\"noopener\"\u003eEclipse Smart-Heat Electric cut sheet (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003ePole options, heat area, minimum floor clearance\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/product\/eclipse-8-inch-straight-pole\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic Eclipse 8 Inch Straight Pole product page\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003ePart number, finish, close-to-ceiling purpose\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/warranty\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic warranty terms\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eWarranty periods by product line\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"Default Title","offer_id":68167514915095,"sku":"BH3230001","price":108.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-eclipse-8-inch-straight-pole-bh3230001-pole-with-heater.jpg?v=1794343257"},{"product_id":"bromic-eclipse-24-inch-straight-pole","title":"Bromic Eclipse 24 Inch Straight Pole - BH3230002","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe Bromic Eclipse 24 Inch Straight Pole (BH3230002) is a single straight ceiling mount pole that hangs an \u003ca href=\"\/products\/bromic-eclipse-smart-heat-electric-2900w-pendant-heater\"\u003eEclipse Smart-Heat Electric 2900W heater\u003c\/a\u003e from a ceiling. It is the single-upright alternative to the 24 in. twin pole that ships with the heater. It is double-coated steel in matte black to match the heater head, which is sold separately.\u003c\/p\u003e\n\u003cp\u003eBromic describes it as a more minimal version of the standard 24 in. twin pole: one upright instead of two, at the same 24 in. drop, with the cable running up inside it into the roof cavity. The other Eclipse poles are \u003ca href=\"\/products\/bromic-eclipse-8-inch-straight-pole\"\u003e8 in. straight (BH3230001)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-twin-pole\"\u003e24 in. twin (BH3230003)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-curved-pole\"\u003e24 in. curved (BH3230004)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-48-inch-straight-pole\"\u003e48 in. straight (BH3230005)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-wall-mount-pole\"\u003ewall mount (BH3230006)\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003ePlan before ordering: the heater head must hang level and at least 8 ft above the floor, so allow for the 24 in. pole and the 4.4 in. head when checking the ceiling height. The pendant mount roof bracket is fixed into structural supports, not ceiling panels alone, and the heater is hard-wired by a licensed electrical contractor, with two people to lift the 30 lb head.\u003c\/p\u003e\n\u003cul class=\"mnk-glance\"\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003ePart number:\u003c\/strong\u003e BH3230002\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eLength:\u003c\/strong\u003e 24 in., straight\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFits:\u003c\/strong\u003e Eclipse Smart-Heat Electric 2900W heater head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFinish:\u003c\/strong\u003e Matte black, double-coated steel\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"features\"\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOne upright, same drop:\u003c\/strong\u003e a single 24 in. pole for a cleaner line than the twin pole the heater ships with.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConcealed cable:\u003c\/strong\u003e the heater cable runs up inside the pole and out into the roof cavity, so no wiring shows below the ceiling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRound ceiling cap:\u003c\/strong\u003e a round cap slides over the pole and covers the roof bracket for a clean finish at the ceiling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuick head fitting:\u003c\/strong\u003e the heater bracket's two pre-fitted screws hook into a slot in the pole, then two more screws lock it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDouble-coated steel in matte black:\u003c\/strong\u003e matches the Eclipse heater head and resists corrosion.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eIdentification\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eEclipse Smart-Heat Electric accessory\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eBH3230002\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eType\u003c\/th\u003e\n\u003ctd\u003eStraight ceiling mount pole\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003eEclipse Smart-Heat Electric 2900W heater head, 240V (BH0920001-2) or 208V (BH0920003); head not included\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eBuild\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLength\u003c\/th\u003e\n\u003ctd\u003e24 in.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eDouble-coated steel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eMatte black\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCeiling fixing\u003c\/th\u003e\n\u003ctd\u003ePendant mount roof bracket, fasteners in four opposing holes into structural supports (fasteners installer supplied)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePole to bracket\u003c\/th\u003e\n\u003ctd\u003e4 x M4 x 6 mm dome head screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCap to bracket\u003c\/th\u003e\n\u003ctd\u003eRound cap, 2 x M4 x 10 mm dome head screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHead to pole\u003c\/th\u003e\n\u003ctd\u003e2 pre-fitted plus 2 extra M4 x 6 mm dome head screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eHeater it carries\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater head\u003c\/th\u003e\n\u003ctd\u003e27.6 x 27.6 x 4.4 in., 30 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMinimum height above floor\u003c\/th\u003e\n\u003ctd\u003e8 ft (96 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eClearance in front of head\u003c\/th\u003e\n\u003ctd\u003e3.3 ft to floors, furniture, plants and heat-sensitive materials\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBetween heaters\u003c\/th\u003e\n\u003ctd\u003e20 in., from the heater edge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003cdiv class=\"mnk-kit\"\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"whats-included\"\u003eWhat's included\u003c\/h3\u003e\n\u003cul class=\"mnk-included\"\u003e\n\u003cli\u003eEclipse 24 in. straight pole, BH3230002\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBromic does not publish a separate packing list for the pole. In the heater's ceiling kit the manual lists the pole assembly with six M4 x 6 mm and two M4 x 10 mm dome head screws, and the steps use a pendant mount roof bracket and round cap; ask us to confirm which of these ship with the pole before ordering. Not included: the heater head and the ceiling fasteners.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"sold-separately\"\u003eSold separately\u003c\/h3\u003e\n\u003cul class=\"mnk-optional\"\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/bromic-eclipse-smart-heat-electric-2900w-pendant-heater\"\u003eEclipse Smart-Heat Electric 2900W heater\u003c\/a\u003e, 240V (BH0920001-2) or 208V (BH0920003); ships with the 24 in. twin pole\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/bromic-affinity-smart-heat-eclipse-controller\"\u003eAffinity Smart-Heat Eclipse controller\u003c\/a\u003e, 1 or 5 channel, for heat and light control with the app\u003c\/li\u003e\n\u003cli\u003eCeiling mount pole screw set, BH8380009 (replacement fixings; ask us)\u003c\/li\u003e\n\u003cli\u003eOther poles: \u003ca href=\"\/products\/bromic-eclipse-8-inch-straight-pole\"\u003e8 in. straight (BH3230001)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-twin-pole\"\u003e24 in. twin (BH3230003)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-curved-pole\"\u003e24 in. curved (BH3230004)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-48-inch-straight-pole\"\u003e48 in. straight (BH3230005)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-wall-mount-pole\"\u003ewall mount (BH3230006)\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003ch3 id=\"installation\"\u003eInstallation planning\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstaller:\u003c\/strong\u003e a licensed electrical contractor or authorized technician, to local codes. Two people are needed; Bromic sets a safe lift of 35 lb per person, and the head weighs 30 lb.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRoof bracket:\u003c\/strong\u003e fasten the pendant mount roof bracket to the ceiling with bolts sized for the surface (not included) in four opposing holes, into structural supports rather than ceiling panels alone. Bromic gives no load rating for the ceiling mount, so the installer chooses fasteners for the load.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePole and cap:\u003c\/strong\u003e attach the pole to the bracket with four M4 x 6 mm screws, then slide the round cap over the pole and fix it to the bracket with two M4 x 10 mm screws.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting the head:\u003c\/strong\u003e keep the cardboard on the head until it is mounted. Feed the cable up through the pole into the roof cavity and take up the slack, hook the heater bracket's two pre-fitted M4 screws into the slot in the pole, add two more M4 x 6 mm screws and tighten all four.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePosition:\u003c\/strong\u003e the head must be level (check with a spirit level), at least 8 ft above the floor, not directly above or in front of an electrical outlet and never facing the ceiling, with 3.3 ft clear in front and to heat-sensitive materials in every direction, and 20 in. between heaters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeather and location:\u003c\/strong\u003e the heater is IP54; Bromic recommends a covered position out of the rain. Keep it away from pools, showers and other water and from areas where flammable liquids are used. Remove all packaging before switching on.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCare:\u003c\/strong\u003e Bromic asks for an inspection before use and a service at least once a year by a qualified technician. Switch off, disconnect power and let the heater cool for at least 2 hours before cleaning. Clean the pole and head with a soft, damp microfiber cloth and lukewarm water with mild dish soap, in gentle strokes in one direction, and let it air dry; do not use abrasive pads, harsh chemicals or a water spray, and do not paint any surface. Near the coast, clean every two weeks and after salt exposure. Do not use the heater if the head or pole is loose, and do not hang anything from the pole.\u003c\/p\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's warranty page does not list a separate term for the Eclipse poles. The Eclipse Pendant heater is covered for 3 years, for the original owner only: Bromic supplies a replacement heater or part, and the owner pays labor, removal and reinstallation, shipping both ways and other costs. Implied warranties are limited to one year. Claims start with the dealer who sold the product. Ask us to confirm the pole's coverage before you order.\u003c\/p\u003e\n\u003ch3 id=\"manuals\"\u003eManuals and documents\u003c\/h3\u003e\n\u003cul class=\"mnk-docs\"\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/BMC-00693-Bromic-Eclipse-Electric-Pendant-Instruction-Manual-US_REV2_20250328.pdf\" target=\"_blank\" rel=\"noopener\"\u003eEclipse Smart-Heat Electric pendant instruction manual, Version 2 US, BMC-00693 (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eSingle pole ceiling steps, kit contents, clearances, care, spare parts\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2026\/01\/Product-Cut-Sheet-Eclipse-Electric.pdf\" target=\"_blank\" rel=\"noopener\"\u003eEclipse Smart-Heat Electric cut sheet (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003ePole options, minimum floor clearance\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/product\/eclipse-24-inch-straight-pole\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic Eclipse 24 Inch Straight Pole product page\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003ePart number, finish, twin pole comparison\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/warranty\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic warranty terms\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eWarranty periods by product line\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e","brand":"Bromic Heating","offers":[{"title":"Default Title","offer_id":68167514980631,"sku":"BH3230002","price":108.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-eclipse-24-inch-straight-pole-bh3230002-pole-with-heater.jpg?v=1794343257"},{"product_id":"bromic-eclipse-24-inch-twin-pole","title":"Bromic Eclipse 24 Inch Twin Pole - BH3230003","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe Bromic Eclipse 24 Inch Twin Pole (BH3230003) is the twin straight ceiling pole that hangs an \u003ca href=\"\/products\/bromic-eclipse-smart-heat-electric-2900w-pendant-heater\"\u003eEclipse Smart-Heat Electric 2900W heater\u003c\/a\u003e from a ceiling. Bromic supplies one free with every Eclipse Electric heater head, so this listing is for a replacement or a spare. It is double-coated steel in matte black to match the heater.\u003c\/p\u003e\n\u003cp\u003eThe pole is two 24 in. uprights fixed to a twin pole roof bracket, with a cap that covers the bracket at the ceiling. The heater's cable runs up through one of the two uprights into the roof cavity, so no wiring shows below the ceiling. For a different drop, Bromic offers \u003ca href=\"\/products\/bromic-eclipse-8-inch-straight-pole\"\u003e8 in.\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-straight-pole\"\u003e24 in.\u003c\/a\u003e and \u003ca href=\"\/products\/bromic-eclipse-48-inch-straight-pole\"\u003e48 in.\u003c\/a\u003e straight poles and a \u003ca href=\"\/products\/bromic-eclipse-24-inch-curved-pole\"\u003e24 in. curved pole\u003c\/a\u003e; for a wall, the \u003ca href=\"\/products\/bromic-eclipse-wall-mount-pole\"\u003ewall mount pole\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003ePlan before ordering: the heater head is sold separately. The head must hang level and at least 8 ft above the floor, so allow for the 24 in. pole and the 4.4 in. head when checking the ceiling height. The roof bracket is fixed into structural supports, not ceiling panels alone, and the heater is hard-wired by a licensed electrical contractor, with two people to lift the 30 lb head.\u003c\/p\u003e\n\u003cul class=\"mnk-glance\"\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003ePart number:\u003c\/strong\u003e BH3230003\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eLength:\u003c\/strong\u003e 24 in., twin uprights\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFits:\u003c\/strong\u003e Eclipse Smart-Heat Electric 2900W heater head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFinish:\u003c\/strong\u003e Matte black, double-coated steel\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"features\"\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSame pole as the heater ships with:\u003c\/strong\u003e Bromic includes it with every Eclipse Electric heater head, so a replacement matches exactly.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwin uprights:\u003c\/strong\u003e two 24 in. poles carry the head from a single twin pole roof bracket.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConcealed cable:\u003c\/strong\u003e the heater cable runs inside one upright and out into the roof cavity.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCeiling cap:\u003c\/strong\u003e a twin pole cap covers the roof bracket for a clean finish at the ceiling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDouble-coated steel in matte black:\u003c\/strong\u003e matches the Eclipse heater head and resists corrosion.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eIdentification\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eEclipse Smart-Heat Electric accessory\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eBH3230003\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eType\u003c\/th\u003e\n\u003ctd\u003eTwin straight ceiling mount pole\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003eEclipse Smart-Heat Electric 2900W heater head, 240V or 208V (head not included)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eBuild\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLength\u003c\/th\u003e\n\u003ctd\u003e24 in.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eDouble-coated steel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eMatte black\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCeiling fixing\u003c\/th\u003e\n\u003ctd\u003eTwin pole roof bracket, fasteners in four opposing holes into structural supports (fasteners installer supplied)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePole to bracket\u003c\/th\u003e\n\u003ctd\u003e4 x M4 x 6 mm dome head screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCap to bracket\u003c\/th\u003e\n\u003ctd\u003e2 x M4 x 6 mm dome head screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHead to pole\u003c\/th\u003e\n\u003ctd\u003e2 pre-fitted plus 2 extra M4 x 6 mm dome head screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eHeater it carries\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater head\u003c\/th\u003e\n\u003ctd\u003e27.6 x 27.6 x 4.4 in., 30 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMinimum height above floor\u003c\/th\u003e\n\u003ctd\u003e8 ft (96 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eClearance in front of head\u003c\/th\u003e\n\u003ctd\u003e3.3 ft to floors, furniture, plants and heat-sensitive materials\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBetween heaters\u003c\/th\u003e\n\u003ctd\u003e20 in., from the heater edge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003cdiv class=\"mnk-kit\"\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"whats-included\"\u003eWhat's included\u003c\/h3\u003e\n\u003cul class=\"mnk-included\"\u003e\n\u003cli\u003eEclipse 24 in. twin pole, BH3230003\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBromic does not publish a separate packing list for the pole. In the heater's ceiling kit the manual lists the pole assembly, the twin pole roof bracket and twin pole cap, six M4 x 6 mm and two M4 x 10 mm dome head screws; ask us to confirm which of these ship with the pole before ordering. Not included: the heater head and the ceiling fasteners.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"sold-separately\"\u003eSold separately\u003c\/h3\u003e\n\u003cul class=\"mnk-optional\"\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/bromic-eclipse-smart-heat-electric-2900w-pendant-heater\"\u003eEclipse Smart-Heat Electric 2900W heater\u003c\/a\u003e, 240V (BH0920001-2) or 208V (BH0920003); includes this twin pole\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/bromic-affinity-smart-heat-eclipse-controller\"\u003eAffinity Smart-Heat Eclipse controller\u003c\/a\u003e, 1 or 5 channel, for heat and light control with the app\u003c\/li\u003e\n\u003cli\u003eCeiling mount pole screw set, BH8380009 (replacement fixings; ask us)\u003c\/li\u003e\n\u003cli\u003eOther poles: \u003ca href=\"\/products\/bromic-eclipse-8-inch-straight-pole\"\u003e8 in. straight (BH3230001)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-straight-pole\"\u003e24 in. straight (BH3230002)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-48-inch-straight-pole\"\u003e48 in. straight (BH3230005)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-curved-pole\"\u003e24 in. curved (BH3230004)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-wall-mount-pole\"\u003ewall mount (BH3230006)\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003ch3 id=\"installation\"\u003eInstallation planning\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstaller:\u003c\/strong\u003e a licensed electrical contractor or authorized technician, to local codes. Two people are needed; Bromic sets a safe lift of 35 lb per person, and the head weighs 30 lb.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRoof bracket:\u003c\/strong\u003e fasten the twin pole roof bracket to the ceiling with bolts (not included) in four opposing holes, into structural supports rather than ceiling panels alone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePole and cap:\u003c\/strong\u003e place the twin pole cap loosely on the pole, attach the pole to the bracket with four M4 x 6 mm screws, then slide the cap up and fix it with two M4 x 6 mm screws.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting the head:\u003c\/strong\u003e keep the cardboard on the head until it is mounted. Feed the cable up through one of the two uprights into the roof cavity, hook the heater bracket's two pre-fitted M4 screws into the slot in the pole, add two more M4 x 6 mm screws and tighten all four.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePosition:\u003c\/strong\u003e the head must be level (check with a spirit level), at least 8 ft above the floor, not directly above or in front of an electrical outlet, with 3.3 ft clear in front and 20 in. between heaters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeather and location:\u003c\/strong\u003e the heater is IP54; Bromic recommends a covered position out of the rain. Keep it away from pools, showers and other water and from areas where flammable liquids are used. Remove all packaging before switching on.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCare:\u003c\/strong\u003e Bromic asks for an inspection before use and a service at least once a year by a qualified technician. Switch off, disconnect power and let the heater cool for at least 2 hours before cleaning. Clean the pole and head with a soft, damp microfiber cloth and lukewarm water with mild dish soap; do not use abrasive pads, harsh chemicals or a water spray, and do not paint any surface. Near the coast, clean every two weeks and after salt exposure.\u003c\/p\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's warranty page does not list a separate term for the Eclipse poles. The Eclipse Pendant heater is covered for 3 years, for the original owner only: Bromic supplies a replacement heater or part, and the owner pays labor, removal and reinstallation, shipping both ways and other costs. Implied warranties are limited to one year. Claims start with the dealer who sold the product. Ask us to confirm the pole's coverage before you order.\u003c\/p\u003e\n\u003ch3 id=\"manuals\"\u003eManuals and documents\u003c\/h3\u003e\n\u003cul class=\"mnk-docs\"\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/BMC-00693-Bromic-Eclipse-Electric-Pendant-Instruction-Manual-US_REV2_20250328.pdf\" target=\"_blank\" rel=\"noopener\"\u003eEclipse Smart-Heat Electric pendant instruction manual, Version 2 US, BMC-00693 (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eTwin pole steps, contents, clearances, care, spare parts\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2026\/01\/Product-Cut-Sheet-Eclipse-Electric.pdf\" target=\"_blank\" rel=\"noopener\"\u003eEclipse Smart-Heat Electric cut sheet (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003ePole options, minimum floor clearance\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/product\/eclipse-24-inch-twin-pole\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic Eclipse 24 Inch Twin Pole product page\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003ePart number, finish, included with heater\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/warranty\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic warranty terms\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eWarranty periods by product line\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"Default Title","offer_id":68167515046167,"sku":"BH3230003","price":170.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-eclipse-24-inch-twin-pole-bh3230003-twin-pole-with-heater.jpg?v=1794343257"},{"product_id":"bromic-eclipse-24-inch-curved-pole","title":"Bromic Eclipse 24 Inch Curved Pole - BH3230004","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe Bromic Eclipse 24 Inch Curved Pole (BH3230004) is a single curved ceiling mount pole that hangs an \u003ca href=\"\/products\/bromic-eclipse-smart-heat-electric-2900w-pendant-heater\"\u003eEclipse Smart-Heat Electric 2900W heater\u003c\/a\u003e from a ceiling. It is a shaped alternative to the 24 in. twin pole that ships with the heater. It is double-coated steel in matte black to match the heater head, which is sold separately.\u003c\/p\u003e\n\u003cp\u003eIt installs the same way as the straight poles, with the cable running up inside it into the roof cavity; Bromic gives no separate angle setting for the curve, and the heater head must still hang level. The other Eclipse poles are \u003ca href=\"\/products\/bromic-eclipse-8-inch-straight-pole\"\u003e8 in. straight (BH3230001)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-straight-pole\"\u003e24 in. straight (BH3230002)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-twin-pole\"\u003e24 in. twin (BH3230003)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-48-inch-straight-pole\"\u003e48 in. straight (BH3230005)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-wall-mount-pole\"\u003ewall mount (BH3230006)\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003ePlan before ordering: the heater head must hang level and at least 8 ft above the floor, so allow for the 24 in. pole and the 4.4 in. head when checking the ceiling height. The pendant mount roof bracket is fixed into structural supports, not ceiling panels alone, and the heater is hard-wired by a licensed electrical contractor, with two people to lift the 30 lb head.\u003c\/p\u003e\n\u003cul class=\"mnk-glance\"\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003ePart number:\u003c\/strong\u003e BH3230004\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eLength:\u003c\/strong\u003e 24 in., curved\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFits:\u003c\/strong\u003e Eclipse Smart-Heat Electric 2900W heater head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFinish:\u003c\/strong\u003e Matte black, double-coated steel\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"features\"\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCurved profile:\u003c\/strong\u003e a 24 in. curved pole in place of the straight twin pole the heater ships with.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConcealed cable:\u003c\/strong\u003e the heater cable runs up inside the pole and out into the roof cavity, so no wiring shows below the ceiling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRound ceiling cap:\u003c\/strong\u003e a round cap slides over the pole and covers the roof bracket for a clean finish at the ceiling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuick head fitting:\u003c\/strong\u003e the heater bracket's two pre-fitted screws hook into a slot in the pole, then two more screws lock it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDouble-coated steel in matte black:\u003c\/strong\u003e matches the Eclipse heater head and resists corrosion.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eIdentification\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eEclipse Smart-Heat Electric accessory\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eBH3230004\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eType\u003c\/th\u003e\n\u003ctd\u003eCurved ceiling mount pole\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003eEclipse Smart-Heat Electric 2900W heater head, 240V (BH0920001-2) or 208V (BH0920003); head not included\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eBuild\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLength\u003c\/th\u003e\n\u003ctd\u003e24 in.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eDouble-coated steel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eMatte black\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCeiling fixing\u003c\/th\u003e\n\u003ctd\u003ePendant mount roof bracket, fasteners in four opposing holes into structural supports (fasteners installer supplied)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePole to bracket\u003c\/th\u003e\n\u003ctd\u003e4 x M4 x 6 mm dome head screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCap to bracket\u003c\/th\u003e\n\u003ctd\u003eRound cap, 2 x M4 x 10 mm dome head screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHead to pole\u003c\/th\u003e\n\u003ctd\u003e2 pre-fitted plus 2 extra M4 x 6 mm dome head screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eHeater it carries\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater head\u003c\/th\u003e\n\u003ctd\u003e27.6 x 27.6 x 4.4 in., 30 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMinimum height above floor\u003c\/th\u003e\n\u003ctd\u003e8 ft (96 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eClearance in front of head\u003c\/th\u003e\n\u003ctd\u003e3.3 ft to floors, furniture, plants and heat-sensitive materials\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBetween heaters\u003c\/th\u003e\n\u003ctd\u003e20 in., from the heater edge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003cdiv class=\"mnk-kit\"\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"whats-included\"\u003eWhat's included\u003c\/h3\u003e\n\u003cul class=\"mnk-included\"\u003e\n\u003cli\u003eEclipse 24 in. curved pole, BH3230004\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBromic does not publish a separate packing list for the pole. In the heater's ceiling kit the manual lists the pole assembly with six M4 x 6 mm and two M4 x 10 mm dome head screws, and the steps use a pendant mount roof bracket and round cap; ask us to confirm which of these ship with the pole before ordering. Not included: the heater head and the ceiling fasteners.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"sold-separately\"\u003eSold separately\u003c\/h3\u003e\n\u003cul class=\"mnk-optional\"\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/bromic-eclipse-smart-heat-electric-2900w-pendant-heater\"\u003eEclipse Smart-Heat Electric 2900W heater\u003c\/a\u003e, 240V (BH0920001-2) or 208V (BH0920003); ships with the 24 in. twin pole\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/bromic-affinity-smart-heat-eclipse-controller\"\u003eAffinity Smart-Heat Eclipse controller\u003c\/a\u003e, 1 or 5 channel, for heat and light control with the app\u003c\/li\u003e\n\u003cli\u003eCeiling mount pole screw set, BH8380009 (replacement fixings; ask us)\u003c\/li\u003e\n\u003cli\u003eOther poles: \u003ca href=\"\/products\/bromic-eclipse-8-inch-straight-pole\"\u003e8 in. straight (BH3230001)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-straight-pole\"\u003e24 in. straight (BH3230002)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-twin-pole\"\u003e24 in. twin (BH3230003)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-48-inch-straight-pole\"\u003e48 in. straight (BH3230005)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-wall-mount-pole\"\u003ewall mount (BH3230006)\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003ch3 id=\"installation\"\u003eInstallation planning\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstaller:\u003c\/strong\u003e a licensed electrical contractor or authorized technician, to local codes. Two people are needed; Bromic sets a safe lift of 35 lb per person, and the head weighs 30 lb.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRoof bracket:\u003c\/strong\u003e fasten the pendant mount roof bracket to the ceiling with bolts sized for the surface (not included) in four opposing holes, into structural supports rather than ceiling panels alone. Bromic gives no load rating for the ceiling mount, so the installer chooses fasteners for the load.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePole and cap:\u003c\/strong\u003e attach the pole to the bracket with four M4 x 6 mm screws, then slide the round cap over the pole and fix it to the bracket with two M4 x 10 mm screws.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting the head:\u003c\/strong\u003e keep the cardboard on the head until it is mounted. Feed the cable up through the pole into the roof cavity and take up the slack, hook the heater bracket's two pre-fitted M4 screws into the slot in the pole, add two more M4 x 6 mm screws and tighten all four.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePosition:\u003c\/strong\u003e the head must be level (check with a spirit level), at least 8 ft above the floor, not directly above or in front of an electrical outlet and never facing the ceiling, with 3.3 ft clear in front and to heat-sensitive materials in every direction, and 20 in. between heaters. The curve has no adjustment; level the head itself.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeather and location:\u003c\/strong\u003e the heater is IP54; Bromic recommends a covered position out of the rain. Keep it away from pools, showers and other water and from areas where flammable liquids are used. Remove all packaging before switching on.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCare:\u003c\/strong\u003e Bromic asks for an inspection before use and a service at least once a year by a qualified technician. Switch off, disconnect power and let the heater cool for at least 2 hours before cleaning. Clean the pole and head with a soft, damp microfiber cloth and lukewarm water with mild dish soap, in gentle strokes in one direction, and let it air dry; do not use abrasive pads, harsh chemicals or a water spray, and do not paint any surface. Near the coast, clean every two weeks and after salt exposure. Do not use the heater if the head or pole is loose, and do not hang anything from the pole.\u003c\/p\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's warranty page does not list a separate term for the Eclipse poles. The Eclipse Pendant heater is covered for 3 years, for the original owner only: Bromic supplies a replacement heater or part, and the owner pays labor, removal and reinstallation, shipping both ways and other costs. Implied warranties are limited to one year. Claims start with the dealer who sold the product. Ask us to confirm the pole's coverage before you order.\u003c\/p\u003e\n\u003ch3 id=\"manuals\"\u003eManuals and documents\u003c\/h3\u003e\n\u003cul class=\"mnk-docs\"\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/BMC-00693-Bromic-Eclipse-Electric-Pendant-Instruction-Manual-US_REV2_20250328.pdf\" target=\"_blank\" rel=\"noopener\"\u003eEclipse Smart-Heat Electric pendant instruction manual, Version 2 US, BMC-00693 (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eSingle pole ceiling steps, kit contents, clearances, care, spare parts\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2026\/01\/Product-Cut-Sheet-Eclipse-Electric.pdf\" target=\"_blank\" rel=\"noopener\"\u003eEclipse Smart-Heat Electric cut sheet (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003ePole options, minimum floor clearance\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/warranty\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic warranty terms\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eWarranty periods by product line\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e","brand":"Bromic Heating","offers":[{"title":"Default Title","offer_id":68167515111703,"sku":"BH3230004","price":170.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-eclipse-24-inch-curved-pole-bh3230004-pole-with-heater.jpg?v=1794343246"},{"product_id":"bromic-eclipse-48-inch-straight-pole","title":"Bromic Eclipse 48 Inch Straight Pole - BH3230005","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe Bromic Eclipse 48 Inch Straight Pole (BH3230005) is a single straight ceiling mount pole that hangs an \u003ca href=\"\/products\/bromic-eclipse-smart-heat-electric-2900w-pendant-heater\"\u003eEclipse Smart-Heat Electric 2900W heater\u003c\/a\u003e from a ceiling. It is the longest of the Eclipse ceiling poles, used in place of the 24 in. twin pole that ships with the heater. It is double-coated steel in matte black to match the heater head, which is sold separately.\u003c\/p\u003e\n\u003cp\u003eBromic makes it for high ceilings: the long pole lowers the heater head toward the 8 ft mounting height so heat and light reach the area below. The cable runs up inside the pole into the roof cavity. The other Eclipse poles are \u003ca href=\"\/products\/bromic-eclipse-8-inch-straight-pole\"\u003e8 in. straight (BH3230001)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-straight-pole\"\u003e24 in. straight (BH3230002)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-twin-pole\"\u003e24 in. twin (BH3230003)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-curved-pole\"\u003e24 in. curved (BH3230004)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-wall-mount-pole\"\u003ewall mount (BH3230006)\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003ePlan before ordering: the heater head must hang level and at least 8 ft above the floor, so allow for the 48 in. pole and the 4.4 in. head when checking the ceiling height. The pendant mount roof bracket is fixed into structural supports, not ceiling panels alone, and the heater is hard-wired by a licensed electrical contractor, with two people to lift the 30 lb head.\u003c\/p\u003e\n\u003cul class=\"mnk-glance\"\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003ePart number:\u003c\/strong\u003e BH3230005\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eLength:\u003c\/strong\u003e 48 in., straight\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFits:\u003c\/strong\u003e Eclipse Smart-Heat Electric 2900W heater head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFinish:\u003c\/strong\u003e Matte black, double-coated steel\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"features\"\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLongest Eclipse drop:\u003c\/strong\u003e 48 in., for high ceilings where the shorter poles would leave the heater too high.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConcealed cable:\u003c\/strong\u003e the heater cable runs up inside the pole and out into the roof cavity, so no wiring shows below the ceiling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRound ceiling cap:\u003c\/strong\u003e a round cap slides over the pole and covers the roof bracket for a clean finish at the ceiling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuick head fitting:\u003c\/strong\u003e the heater bracket's two pre-fitted screws hook into a slot in the pole, then two more screws lock it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDouble-coated steel in matte black:\u003c\/strong\u003e matches the Eclipse heater head and resists corrosion.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eIdentification\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eEclipse Smart-Heat Electric accessory\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eBH3230005\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eType\u003c\/th\u003e\n\u003ctd\u003eStraight ceiling mount pole\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003eEclipse Smart-Heat Electric 2900W heater head, 240V (BH0920001-2) or 208V (BH0920003); head not included\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eBuild\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eLength\u003c\/th\u003e\n\u003ctd\u003e48 in.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eDouble-coated steel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eMatte black\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCeiling fixing\u003c\/th\u003e\n\u003ctd\u003ePendant mount roof bracket, fasteners in four opposing holes into structural supports (fasteners installer supplied)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePole to bracket\u003c\/th\u003e\n\u003ctd\u003e4 x M4 x 6 mm dome head screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCap to bracket\u003c\/th\u003e\n\u003ctd\u003eRound cap, 2 x M4 x 10 mm dome head screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHead to pole\u003c\/th\u003e\n\u003ctd\u003e2 pre-fitted plus 2 extra M4 x 6 mm dome head screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eHeater it carries\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater head\u003c\/th\u003e\n\u003ctd\u003e27.6 x 27.6 x 4.4 in., 30 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMinimum height above floor\u003c\/th\u003e\n\u003ctd\u003e8 ft (96 in.)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eClearance in front of head\u003c\/th\u003e\n\u003ctd\u003e3.3 ft to floors, furniture, plants and heat-sensitive materials\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBetween heaters\u003c\/th\u003e\n\u003ctd\u003e20 in., from the heater edge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003cdiv class=\"mnk-kit\"\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"whats-included\"\u003eWhat's included\u003c\/h3\u003e\n\u003cul class=\"mnk-included\"\u003e\n\u003cli\u003eEclipse 48 in. straight pole, BH3230005\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBromic does not publish a separate packing list for the pole. In the heater's ceiling kit the manual lists the pole assembly with six M4 x 6 mm and two M4 x 10 mm dome head screws, and the steps use a pendant mount roof bracket and round cap; ask us to confirm which of these ship with the pole before ordering. Not included: the heater head and the ceiling fasteners.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"sold-separately\"\u003eSold separately\u003c\/h3\u003e\n\u003cul class=\"mnk-optional\"\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/bromic-eclipse-smart-heat-electric-2900w-pendant-heater\"\u003eEclipse Smart-Heat Electric 2900W heater\u003c\/a\u003e, 240V (BH0920001-2) or 208V (BH0920003); ships with the 24 in. twin pole\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/bromic-affinity-smart-heat-eclipse-controller\"\u003eAffinity Smart-Heat Eclipse controller\u003c\/a\u003e, 1 or 5 channel, for heat and light control with the app\u003c\/li\u003e\n\u003cli\u003eCeiling mount pole screw set, BH8380009 (replacement fixings; ask us)\u003c\/li\u003e\n\u003cli\u003eOther poles: \u003ca href=\"\/products\/bromic-eclipse-8-inch-straight-pole\"\u003e8 in. straight (BH3230001)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-straight-pole\"\u003e24 in. straight (BH3230002)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-twin-pole\"\u003e24 in. twin (BH3230003)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-curved-pole\"\u003e24 in. curved (BH3230004)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-wall-mount-pole\"\u003ewall mount (BH3230006)\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003ch3 id=\"installation\"\u003eInstallation planning\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstaller:\u003c\/strong\u003e a licensed electrical contractor or authorized technician, to local codes. Two people are needed; Bromic sets a safe lift of 35 lb per person, and the head weighs 30 lb.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRoof bracket:\u003c\/strong\u003e fasten the pendant mount roof bracket to the ceiling with bolts sized for the surface (not included) in four opposing holes, into structural supports rather than ceiling panels alone. Bromic gives no load rating for the ceiling mount, so the installer chooses fasteners for the load.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePole and cap:\u003c\/strong\u003e attach the pole to the bracket with four M4 x 6 mm screws, then slide the round cap over the pole and fix it to the bracket with two M4 x 10 mm screws.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting the head:\u003c\/strong\u003e keep the cardboard on the head until it is mounted. Feed the cable up through the pole into the roof cavity and take up the slack, hook the heater bracket's two pre-fitted M4 screws into the slot in the pole, add two more M4 x 6 mm screws and tighten all four.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePosition:\u003c\/strong\u003e the head must be level (check with a spirit level), at least 8 ft above the floor, not directly above or in front of an electrical outlet and never facing the ceiling, with 3.3 ft clear in front and to heat-sensitive materials in every direction, and 20 in. between heaters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeather and location:\u003c\/strong\u003e the heater is IP54; Bromic recommends a covered position out of the rain. Keep it away from pools, showers and other water and from areas where flammable liquids are used. Remove all packaging before switching on.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCare:\u003c\/strong\u003e Bromic asks for an inspection before use and a service at least once a year by a qualified technician. Switch off, disconnect power and let the heater cool for at least 2 hours before cleaning. Clean the pole and head with a soft, damp microfiber cloth and lukewarm water with mild dish soap, in gentle strokes in one direction, and let it air dry; do not use abrasive pads, harsh chemicals or a water spray, and do not paint any surface. Near the coast, clean every two weeks and after salt exposure. Do not use the heater if the head or pole is loose, and do not hang anything from the pole.\u003c\/p\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's warranty page does not list a separate term for the Eclipse poles. The Eclipse Pendant heater is covered for 3 years, for the original owner only: Bromic supplies a replacement heater or part, and the owner pays labor, removal and reinstallation, shipping both ways and other costs. Implied warranties are limited to one year. Claims start with the dealer who sold the product. Ask us to confirm the pole's coverage before you order.\u003c\/p\u003e\n\u003ch3 id=\"manuals\"\u003eManuals and documents\u003c\/h3\u003e\n\u003cul class=\"mnk-docs\"\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/BMC-00693-Bromic-Eclipse-Electric-Pendant-Instruction-Manual-US_REV2_20250328.pdf\" target=\"_blank\" rel=\"noopener\"\u003eEclipse Smart-Heat Electric pendant instruction manual, Version 2 US, BMC-00693 (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eSingle pole ceiling steps, kit contents, clearances, care, spare parts\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2026\/01\/Product-Cut-Sheet-Eclipse-Electric.pdf\" target=\"_blank\" rel=\"noopener\"\u003eEclipse Smart-Heat Electric cut sheet (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003ePole options, minimum floor clearance\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/product\/eclipse-48-inch-straight-pole\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic Eclipse 48 Inch Straight Pole product page\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eHigh-ceiling use\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/warranty\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic warranty terms\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eWarranty periods by product line\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e","brand":"Bromic Heating","offers":[{"title":"Default Title","offer_id":68167515210007,"sku":"BH3230005","price":170.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-eclipse-48-inch-straight-pole-bh3230005-pole-with-heater.jpg?v=1794343257"},{"product_id":"bromic-eclipse-wall-mount-pole","title":"Bromic Eclipse Wall Mount Pole - BH3230006","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThe Bromic Eclipse Wall Mount Pole (BH3230006) is a curved arm that mounts an \u003ca href=\"\/products\/bromic-eclipse-smart-heat-electric-2900w-pendant-heater\"\u003eEclipse Smart-Heat Electric 2900W heater\u003c\/a\u003e on a wall or structure instead of hanging it from a ceiling. It is double-coated steel in matte black to match the heater head, and the wall bracket lets the arm swing up to 45 degrees from the wall to each side, so the head can be angled toward the seating.\u003c\/p\u003e\n\u003cp\u003eUse it where the heater has to go on a wall or other structure rather than hang from a ceiling. The heater's cable can run back into the wall cavity through a slot in the bracket, or down through an optional cable slot on the underside. For ceiling mounting, Bromic offers the \u003ca href=\"\/products\/bromic-eclipse-24-inch-twin-pole\"\u003e24 in. twin pole\u003c\/a\u003e (included with the heater), \u003ca href=\"\/products\/bromic-eclipse-8-inch-straight-pole\"\u003e8 in.\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-straight-pole\"\u003e24 in.\u003c\/a\u003e and \u003ca href=\"\/products\/bromic-eclipse-48-inch-straight-pole\"\u003e48 in.\u003c\/a\u003e straight poles and a \u003ca href=\"\/products\/bromic-eclipse-24-inch-curved-pole\"\u003e24 in. curved pole\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003ePlan before ordering: the heater head is sold separately. The head must end up at least 8 ft above the floor and level, with 3.3 ft clear in front of it. The wall bracket is fixed with installer-supplied bolts in all six holes into a structure the installer has assessed, and the heater is hard-wired by a licensed electrical contractor, with two people to lift the 30 lb head.\u003c\/p\u003e\n\u003cul class=\"mnk-glance\"\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003ePart number:\u003c\/strong\u003e BH3230006\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFits:\u003c\/strong\u003e Eclipse Smart-Heat Electric 2900W heater head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eSwing:\u003c\/strong\u003e Up to 45 degrees from the wall, each side\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong class=\"mnk-glance__label\"\u003eFinish:\u003c\/strong\u003e Matte black, double-coated steel\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"features\"\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eWall or structure mounting:\u003c\/strong\u003e puts the Eclipse heater on a wall, column or post where a ceiling pole cannot go.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAdjustable angle:\u003c\/strong\u003e the arm locks at up to 45 degrees from the wall on either side, so heat and light can be directed over the seating.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo cable routes:\u003c\/strong\u003e back into the wall cavity through the bracket slot, or out through an underside slot with a metal M20 cable gland.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBracket cover:\u003c\/strong\u003e a cover slides over the wall bracket for a clean finish.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDouble-coated steel in matte black:\u003c\/strong\u003e matches the Eclipse heater head and resists corrosion.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSized fixings:\u003c\/strong\u003e Bromic gives a calculated tensile load of 675 lbf per screw, with a safety factor of 4, for choosing the wall bolts.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eIdentification\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eEclipse Smart-Heat Electric accessory\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eBH3230006\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eType\u003c\/th\u003e\n\u003ctd\u003eCurved wall mount pole\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003eEclipse Smart-Heat Electric 2900W heater head, 240V or 208V (head not included)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eBuild\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eDouble-coated steel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eMatte black\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eArm angle\u003c\/th\u003e\n\u003ctd\u003eUp to 45 degrees from the wall on each side, locked with two M6 screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eWall fixing\u003c\/th\u003e\n\u003ctd\u003eWall bracket, bolts in all 6 holes (installer supplied)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFixing load\u003c\/th\u003e\n\u003ctd\u003eCalculated tensile load 675 lbf per screw, safety factor 4\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eCable exit\u003c\/th\u003e\n\u003ctd\u003eBack slot into the wall cavity, or underside slot with an M20 metal cable gland (not supplied)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eHeater it carries\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eHeater head\u003c\/th\u003e\n\u003ctd\u003e27.6 x 27.6 x 4.4 in., 30 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eMinimum height above floor\u003c\/th\u003e\n\u003ctd\u003e8 ft (96 in.), wall or ceiling mounting\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eClearance in front of head\u003c\/th\u003e\n\u003ctd\u003e3.3 ft to floors, furniture, plants and heat-sensitive materials\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBetween heaters\u003c\/th\u003e\n\u003ctd\u003e20 in., from the heater edge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003cdiv class=\"mnk-kit\"\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"whats-included\"\u003eWhat's included\u003c\/h3\u003e\n\u003cul class=\"mnk-included\"\u003e\n\u003cli\u003eEclipse wall mount pole, BH3230006\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBromic does not publish a separate packing list for the pole. In Bromic's wall-mount set-up the manual lists the wall mount pole, wall bracket, wall bracket cover, one M8 x 15 mm round head hex screw, one M4 x 10 mm and two M4 x 6 mm dome head screws, two M6 x 10 mm dome head screws and an M20 x 1.5 blanking plug; ask us to confirm which of these ship with the pole before ordering. Not included: the heater head, the wall bolts and the M20 cable gland.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"mnk-kit__col\"\u003e\n\u003ch3 id=\"sold-separately\"\u003eSold separately\u003c\/h3\u003e\n\u003cul class=\"mnk-optional\"\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/bromic-eclipse-smart-heat-electric-2900w-pendant-heater\"\u003eEclipse Smart-Heat Electric 2900W heater\u003c\/a\u003e, 240V (BH0920001-2) or 208V (BH0920003)\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/bromic-affinity-smart-heat-eclipse-controller\"\u003eAffinity Smart-Heat Eclipse controller\u003c\/a\u003e, 1 or 5 channel, for heat and light control with the app\u003c\/li\u003e\n\u003cli\u003eWall mount pole screw set, BH8380010 (replacement fixings; ask us)\u003c\/li\u003e\n\u003cli\u003eCeiling poles: \u003ca href=\"\/products\/bromic-eclipse-24-inch-twin-pole\"\u003e24 in. twin (BH3230003)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-8-inch-straight-pole\"\u003e8 in. straight (BH3230001)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-straight-pole\"\u003e24 in. straight (BH3230002)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-48-inch-straight-pole\"\u003e48 in. straight (BH3230005)\u003c\/a\u003e, \u003ca href=\"\/products\/bromic-eclipse-24-inch-curved-pole\"\u003e24 in. curved (BH3230004)\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003ch3 id=\"installation\"\u003eInstallation planning\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstaller:\u003c\/strong\u003e a licensed electrical contractor or authorized technician, to local codes. Two people are needed; Bromic sets a safe lift of 35 lb per person, and the head weighs 30 lb.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWall bracket:\u003c\/strong\u003e fix it with bolts (not included) in all six holes, into a solid surface the installer has assessed, then slide the bracket cover over it and secure it with one M4 x 10 mm screw.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting the head:\u003c\/strong\u003e keep the cardboard on the head until it is mounted. Feed the cable through the end of the pole, hook the heater bracket's two pre-fitted M4 screws into the slot in the pole with the Bromic logo facing away from the wall, add the two extra M4 x 6 mm screws and tighten all four.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting the pole:\u003c\/strong\u003e attach it to the wall bracket with the M8 x 15 mm hex screw, set the angle (up to 45 degrees each side) and lock it with the two M6 x 10 mm screws. If the cable runs into the wall, close the underside slot with the blanking plug; if it runs out underneath, use an M20 metal cable gland.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePosition:\u003c\/strong\u003e the head must be level (check with a spirit level), at least 8 ft above the floor, not facing the ceiling or heat-sensitive materials, and not directly above or in front of an electrical outlet. Keep 3.3 ft clear in front and 20 in. between heaters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeather and location:\u003c\/strong\u003e the heater is IP54; Bromic recommends a covered position out of the rain. Keep it away from pools, showers and other water and from areas where flammable liquids are used. Remove all packaging before switching on.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCare:\u003c\/strong\u003e Bromic asks for an inspection before use and a service at least once a year by a qualified technician. Switch off, disconnect power and let the heater cool for at least 2 hours before cleaning. Clean the pole and head with a soft, damp microfiber cloth and lukewarm water with mild dish soap; do not use abrasive pads, harsh chemicals or a water spray, and do not paint any surface. Near the coast, clean every two weeks and after salt exposure.\u003c\/p\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's warranty page does not list a separate term for the Eclipse poles. The Eclipse Pendant heater is covered for 3 years, for the original owner only: Bromic supplies a replacement heater or part, and the owner pays labor, removal and reinstallation, shipping both ways and other costs. Implied warranties are limited to one year. Claims start with the dealer who sold the product. Ask us to confirm the pole's coverage before you order.\u003c\/p\u003e\n\u003ch3 id=\"manuals\"\u003eManuals and documents\u003c\/h3\u003e\n\u003cul class=\"mnk-docs\"\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2021\/07\/BMC-00693-Bromic-Eclipse-Electric-Pendant-Instruction-Manual-US_REV2_20250328.pdf\" target=\"_blank\" rel=\"noopener\"\u003eEclipse Smart-Heat Electric pendant instruction manual, Version 2 US, BMC-00693 (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eWall mount pole steps, contents, clearances, care, spare parts\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/pim.bromic.com\/wp-content\/uploads\/2026\/01\/Product-Cut-Sheet-Eclipse-Electric.pdf\" target=\"_blank\" rel=\"noopener\"\u003eEclipse Smart-Heat Electric cut sheet (PDF)\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003ePole options, minimum floor clearance\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/product\/eclipse-wall-mount-pole\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic Eclipse Wall Mount Pole product page\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003ePart number, finish\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/www.bromic.com\/warranty\/\" target=\"_blank\" rel=\"noopener\"\u003eBromic warranty terms\u003c\/a\u003e \u003cspan class=\"mnk-docs__meta\"\u003eWarranty periods by product line\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"Default Title","offer_id":68167515275543,"sku":"BH3230006","price":229.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-eclipse-wall-mount-pole-bh3230006-pole-with-heater.jpg?v=1794343269"},{"product_id":"bromic-smart-heat-gas-ceiling-bracket-paddles-and-screws-bh3030009-1","title":"Bromic Smart-Heat Gas Ceiling Bracket Paddles and Screws - BH3030009-1","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThis is a genuine Bromic Smart-Heat Gas Ceiling Bracket Paddles and Screws (part BH3030009-1) for the Platinum and Tungsten Smart-Heat Gas line.\u003c\/p\u003e\n\u003cp\u003eMatch the part number against your heater's manual before ordering, and call us if you are unsure which one you need. Bromic says service work on its heaters should be done by an authorized, qualified person. See the full \u003ca href=\"\/collections\/bromic-heating\"\u003eBromic Heating\u003c\/a\u003e range.\u003c\/p\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eDetails\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart name\u003c\/th\u003e\n\u003ctd\u003eSmart-Heat Gas Ceiling Bracket Paddles and Screws\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003ePlatinum and Tungsten Smart-Heat Gas\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eBH3030009-1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's published warranty page does not list a separate term for this part. Call us for the current terms before you order.\u003c\/p\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"Default Title","offer_id":68167517012247,"sku":"BH3030009-1","price":153.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-smart-heat-gas-ceiling-bracket-paddles-and-screws-bh3030009-1-front.jpg?v=1794343331"},{"product_id":"bromic-smart-heat-gas-wall-bracket-assembly-with-controls-bh8080001-1","title":"Bromic Smart-Heat Gas Wall Bracket Assembly with Controls - BH8080001-1","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThis is a genuine Bromic Smart-Heat Gas Wall Bracket Assembly with Controls (part BH8080001-1) for the Platinum and Tungsten Smart-Heat Gas line.\u003c\/p\u003e\n\u003cp\u003eMatch the part number against your heater's manual before ordering, and call us if you are unsure which one you need. Bromic says service work on its heaters should be done by an authorized, qualified person. See the full \u003ca href=\"\/collections\/bromic-heating\"\u003eBromic Heating\u003c\/a\u003e range.\u003c\/p\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eDetails\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart name\u003c\/th\u003e\n\u003ctd\u003eSmart-Heat Gas Wall Bracket Assembly with Controls\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003ePlatinum and Tungsten Smart-Heat Gas\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eBH8080001-1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's published warranty page does not list a separate term for this part. Call us for the current terms before you order.\u003c\/p\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"Default Title","offer_id":68167517602071,"sku":"BH8080001-1","price":925.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-smart-heat-gas-wall-bracket-assembly-with-controls-bh8080001-1-front.jpg?v=1794343332"},{"product_id":"bromic-smart-heat-gas-wall-mount-bracket-arm-bh8080021","title":"Bromic Smart-Heat Gas Wall Mount Bracket Arm - BH8080021","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThis is a genuine Bromic Smart-Heat Gas Wall Mount Bracket Arm (part BH8080021) for the Platinum and Tungsten Smart-Heat Gas line.\u003c\/p\u003e\n\u003cp\u003eMatch the part number against your heater's manual before ordering, and call us if you are unsure which one you need. Bromic says service work on its heaters should be done by an authorized, qualified person. See the full \u003ca href=\"\/collections\/bromic-heating\"\u003eBromic Heating\u003c\/a\u003e range.\u003c\/p\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eDetails\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart name\u003c\/th\u003e\n\u003ctd\u003eSmart-Heat Gas Wall Mount Bracket Arm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003ePlatinum and Tungsten Smart-Heat Gas\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eBH8080021\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's published warranty page does not list a separate term for this part. Call us for the current terms before you order.\u003c\/p\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"Default Title","offer_id":68167517667607,"sku":"BH8080021","price":99.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-smart-heat-gas-wall-mount-bracket-arm-bh8080021-bracket-arm.jpg?v=1794343332"},{"product_id":"bromic-platinum-electric-wall-bracket-and-covers-set-bh3130028","title":"Bromic Platinum Electric Wall Bracket and Covers Set - BH3130028","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThis is a genuine Bromic Platinum Electric Wall Bracket and Covers Set (part BH3130028) for the Platinum Smart-Heat Electric line.\u003c\/p\u003e\n\u003cp\u003eMatch the part number against your heater's manual before ordering, and call us if you are unsure which one you need. Bromic says service work on its heaters should be done by an authorized, qualified person. See the full \u003ca href=\"\/collections\/bromic-heating\"\u003eBromic Heating\u003c\/a\u003e range.\u003c\/p\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eDetails\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart name\u003c\/th\u003e\n\u003ctd\u003ePlatinum Electric Wall Bracket and Covers Set\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003ePlatinum Smart-Heat Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eBH3130028\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's published warranty page does not list a separate term for this part. Call us for the current terms before you order.\u003c\/p\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"Default Title","offer_id":68167520583959,"sku":"BH3130028","price":351.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-platinum-electric-wall-bracket-and-covers-set-bh3130028-front.jpg?v=1794343294"},{"product_id":"bromic-tungsten-electric-short-mounting-brackets-black-bh8180008","title":"Bromic Tungsten Electric Short Mounting Brackets Black - BH8180008","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThis is a genuine Bromic Tungsten Electric Short Mounting Brackets Black (part BH8180008) for the Tungsten Smart-Heat Electric line.\u003c\/p\u003e\n\u003cp\u003eMatch the part number against your heater's manual before ordering, and call us if you are unsure which one you need. Bromic says service work on its heaters should be done by an authorized, qualified person. See the full \u003ca href=\"\/collections\/bromic-heating\"\u003eBromic Heating\u003c\/a\u003e range.\u003c\/p\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eDetails\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart name\u003c\/th\u003e\n\u003ctd\u003eTungsten Electric Short Mounting Brackets Black\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003eTungsten Smart-Heat Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eBH8180008\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's published warranty page does not list a separate term for this part. Call us for the current terms before you order.\u003c\/p\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"Default Title","offer_id":68167523664151,"sku":"BH8180008","price":59.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-tungsten-electric-short-mounting-brackets-black-bh8180008-front.jpg?v=1794343343"},{"product_id":"bromic-tungsten-electric-short-mounting-brackets-white-bh8180021","title":"Bromic Tungsten Electric Short Mounting Brackets White - BH8180021","description":"\u003ch2 id=\"description\" data-mnk-layout=\"1\"\u003eDescription\u003c\/h2\u003e\n\u003cp\u003eThis is a genuine Bromic Tungsten Electric Short Mounting Brackets White (part BH8180021) for the Tungsten Smart-Heat Electric line.\u003c\/p\u003e\n\u003cp\u003eMatch the part number against your heater's manual before ordering, and call us if you are unsure which one you need. Bromic says service work on its heaters should be done by an authorized, qualified person. See the full \u003ca href=\"\/collections\/bromic-heating\"\u003eBromic Heating\u003c\/a\u003e range.\u003c\/p\u003e\n\u003ch2 id=\"specifications\"\u003eSpecifications\u003c\/h2\u003e\n\u003ctable class=\"mnk-specs\"\u003e\u003ctbody\u003e\n\u003ctr class=\"mnk-specs__group\"\u003e\u003cth colspan=\"2\" scope=\"colgroup\"\u003eDetails\u003c\/th\u003e\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart name\u003c\/th\u003e\n\u003ctd\u003eTungsten Electric Short Mounting Brackets White\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eFits\u003c\/th\u003e\n\u003ctd\u003eTungsten Smart-Heat Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eBH8180021\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth scope=\"row\"\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBromic Heating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch3 id=\"warranty\"\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBromic's published warranty page does not list a separate term for this part. Call us for the current terms before you order.\u003c\/p\u003e\n\u003ch3 id=\"legal\"\u003eLegal disclaimers and warnings\u003c\/h3\u003e\n\u003cp class=\"mnk-legal\"\u003eProduct packaging, owners' manuals, installation instructions, and\/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product.\u003c\/p\u003e\n","brand":"Bromic Heating","offers":[{"title":"Default Title","offer_id":68167523795223,"sku":"BH8180021","price":64.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/files\/bromic-tungsten-electric-short-mounting-brackets-white-bh8180021-front.jpg?v=1794343343"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1251\/8981\/collections\/bromic-heater-mounts-low-clearance-recess-kit.jpg?v=1794168461","url":"https:\/\/mnkgrills.com\/collections\/bromic-heater-mounts.oembed","provider":"M\u0026K Grills","version":"1.0","type":"link"}