Blaze LTE+ Built-In Double Side Burner W/ Stainless Steel Lid - BLZ-SB2-LTEPLUS

Features

• Two 12,000 BTU brass burners: run one for a simmer or both at once, each on its own knob.
• Compact 12-1/2" width: adds two burners while taking little counter space from the island.
• LTE+ lighting: LED backlit knobs with safety glow that show when gas is flowing, for safe cooking after dark.
• Removable stainless steel cover: keeps rain and debris off the burners between uses.
• Push-and-turn ignition: piezo ignition with a flash tube backup, plus manual match-lighting if needed.
• Lifetime coverage on the core: burners, grates, body and valves carry a Blaze lifetime warranty (parts) when registered.

Specifications

Installation planning

• Cut-out: 11" W x 20-3/4" D x 8-1/2" H. Cut a 1" air gap in the front face of the countertop below the control panel.
• Install in a non-combustible enclosure only; the local fire marshal, building inspector or authority having jurisdiction decides what counts as combustible. A combustible island needs a Blaze insulated jacket.
• Clearances: 18" from combustible material at the sides and back. Never install under combustible overhead construction or an awning. Under a non-combustible overhead, keep 72" of clearance and run a UL-approved vent hood of at least 1,000 CFM that covers the cooking area, with the fan bottom at least 36" above the cooking surface.
• Vent the island on both sides: upper vents within 5" of the island top (at least 1 sq. in. of free area per lb of stored fuel, per vent) and lower vents within 1" of the floor and no more than 5" high (at least 1/2 sq. in. per lb, per vent). Every opening must pass a 1/8" rod. Propane is heavier than air and natural gas is lighter, so both vent levels matter.
• Outdoors means up to three walls with no roof, or a roof with no more than two walls, all openings permanently open; windows, doors and screens do not count. Not for garages, enclosed areas, RVs or boats, and not near a window or vent into the house. In a windy spot, use a wind break: wind from the rear can push heat behind the control panel.
• Natural gas: the regulator is factory-set for natural gas at 4" water column; use a flex connector of at least 5/8" diameter at the rear right corner, and seal non-flared fittings with rated thread sealant. Inlet pressure above about 1/2 psi needs another regulator first. The installer supplies an accessible shut-off valve.
• Propane: a 20 lb cylinder (12-1/4" diameter x 18" high, with an overfill prevention device) uses the factory LP hose and regulator only (3/8" flare, no pipe sealant; hand-tighten the regulator to the cylinder). Keep only one cylinder in the island, upright. Plumbed (bulk) propane at 11" water column requires a licensed gas professional to reset the convertible regulator; never use that regulator with a 20 lb cylinder.
• Fuel conversion (orifice change, regulator setting, air shutter about 1/8" open for natural gas and 1/4" for propane) is for a licensed gas professional only.
• Electrical: plug the light transformer into a 15-amp GFI-protected circuit; outdoor extension cords must be rated "W" or "W-A" and kept off hot surfaces.
• Leak-test every connection with a 1:1 soap and water solution before each use, after installation and whenever a connection changes. Never use a flame to check for leaks.
• Lighting: remove the cover, push the knob in and turn it to HIGH until it clicks. If it does not light within 5 seconds, turn it off and wait 5 minutes before trying again. Flames should be mostly blue and not lift off the burner.

Care: Clean the grate after every use while it is still warm: brush it, wipe it with a 50/50 vinegar and water solution, dry it with a microfiber cloth and oil it lightly. Wash the drip tray in hot soapy water once cool. Wipe stainless steel along the grain with a stainless steel cleaner and avoid harsh abrasives. Never flood a hot unit with cold water, and never cover it while damp or warm.

Warranty

Blaze residential warranty, parts only: lifetime on the main burners, grates, body and valves (and other stainless steel components); 1 year on the ignition and on the lighting and electrical parts. For multi-user use, Blaze covers the stainless housing, burners, rod grids, brass valves, inner liners and manifolds for 3 years and other parts (except burners) for 90 days; restaurant use is not covered. Coverage is for the original owner at the original installation site in the United States and Canada and does not transfer. Register the burner with Blaze within 30 days of purchase and keep your receipt. Labor, shipping and diagnostic charges are not covered, nor are discoloration or surface rust (unless structural integrity is lost), damage from poor maintenance, chemicals, chlorine or salt, unapproved alterations, or installation by an unqualified person. Full terms are in the user manual.

Manuals and documents

• Blaze LTE+ double side burner user manual, BLZ-SB2-LTEPLUS / BLZ-SB2LTE3 (PDF)
• Blaze BLZ-SB2LTE3 spec sheet (PDF)
• Blaze product page: LTE+ Double Side Burner
• Blaze product registration

Legal disclaimers and warnings

Product packaging, owners' manuals, installation instructions, and/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product. WARNING: This product can expose you to chemicals including chromium (hexavalent compounds), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.