

Features
- Required for combustible islands: lets you build a Blaze LTE or Traditional power burner into a wood-framed or other combustible enclosure, as the burner manual requires.
- Made for the shorter burners: 9" tall; cut-out 16-1/2" W x 20-1/2" D x 8-3/4" H.
- Stainless steel construction: built for outdoor use and gives the island opening a finished stainless look.
- Self-supporting ledge: runs around the sides and back so the jacket rests on the countertop opening.
- Lifetime warranty: Blaze covers the jacket against defects in manufacturing and workmanship for the original purchaser.
Specifications
| Brand | Blaze |
|---|---|
| Model | BLZ-PB-IJ |
| Type | Insulated jacket for a built-in power burner |
| Fits (per Blaze) | Blaze LTE / Traditional built-in power burners, including the Premium LTE power burner (BLZ-PBLTE-LP / NG) |
| Not for | Professional LUX and LTE PRO power burners (use BLZ-PROPB-IJ) |
| Overall width | 18-1/8" |
| Overall depth | 21-3/8" |
| Overall height | 9" |
| Cut-out width | 16-1/2" |
| Cut-out depth | 20-1/2" |
| Cut-out height | 8-3/4" |
| Cut-out note | 1/4" to 1/2" gap possible below the jacket |
| Material | Stainless steel |
| Construction | Self-supporting ledge around the sides and back |
| Use | Required when the island is built from combustible materials |
| Warranty | Lifetime, defects in manufacturing and workmanship (original purchaser, single-family home use) |
What's included
- Stainless steel insulated jacket for one LTE or Traditional power burner
Blaze publishes no packing list, hardware count or weight for this jacket. The power burner is sold separately.
Sold separately
- Blaze Premium LTE built-in power burner (BLZ-PBLTE): a burner this jacket is made for.
- Blaze insulated jacket for 32-inch Prelude LBM and Premium LTE grills (BLZ-4-IJ): for a matching Premium LTE grill in the same combustible island.
- Blaze 6 x 14 stainless island vent panel (BLZ-ISLAND-VENT): the power burner manual says stainless vent panels are available to cover the island venting.
- Blaze roll-out trash and propane tank drawer (BLZ-TRLP-DRW-H): the manual names Blaze's propane tank drawer as an alternative to a plenum wall for a tank inside the island.
Installation planning
- Cut the island opening to the jacket cut-out: 16-1/2" W x 20-1/2" D x 8-3/4" H. Blaze notes that a 1/4" to 1/2" gap is possible below the insulated jacket, so allow for it when you build the opening.
- Without a jacket, the power burner manual gives the BLZ-PBLTE a 14" W x 19-1/2" D x 8" H size; that applies only to non-combustible islands, and the opening must not be larger than the burner's outer frame.
- Power burner manual (version 1.0, BLZ-PBLTE / BLZ-PROPB): keep at least 16" from combustible material at the sides and back. The burner must not be located under overhead construction or where an overhang or awning may cover it.
- Vent the island: propane is heavier than air and settles low, natural gas is lighter and rises, so vent for your fuel. A propane cylinder inside the island needs a plenum wall or Blaze's propane tank drawer.
- Gas: natural gas runs at 4" water column (flex connector at least 1/2" diameter) and propane at 11" water column. The installer supplies an accessible shut-off valve; Massachusetts requires a T-handle valve.
- A licensed professional contractor should install the jacket, and a licensed gas professional should make every gas connection (Blaze insulated jacket installation sheet).
- Blaze does not allow a rubber gas line connected directly to the appliance inside the jacket, even one supplied with it: use a stainless steel flex line. The appliance's fittings may not suit every installation, so different fittings or a pipe extension may be needed to avoid kinks and keep excess line out of the jacket.
- Leak-check every gas connection as the final step and correct any leak before use.
- The jacket protects combustible material from the cooking surface down only. The appliance manual's clearances above, behind and beside the appliance still apply.
Warranty
Blaze states that its insulated jackets are covered by a lifetime warranty against defects in manufacturing and workmanship. The warranty extends to the original purchaser and applies to products bought for ordinary single-family home use. Blaze's product page gives no further conditions or exclusions for the jacket; the power burner you set in it carries its own warranty, set out in its manual. Register the product with Blaze after delivery.
Manuals and documents
- Blaze product page: Power Burner Insulated Jackets (BLZ-PB-IJ and BLZ-PROPB-IJ)
- Blaze Insulated Jacket Installation sheet (PDF)
- Blaze power burner manual, version 1.0, BLZ-PBLTE / BLZ-PROPB (PDF)
- Blaze product registration
Legal disclaimers and warnings
Product packaging, owners' manuals, installation instructions, and/or operating instructions may include more information than what is shown on our website. The content on our site is intended to be used for reference purposes only. Please fully read all included manuals and documentation before installing or using this product. WARNING: This product can expose you to chemicals including chromium (hexavalent compounds), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
